HamStudy.org: Questions that need explanations in CA_B

2025 Basic Qualification pool

467 / 984 questions need explanations

52.5% complete

All explanations are written and maintained by ordinary users like you! Please help us finish the explanations in this pool.

B-003-008-001

If a linear power supply provides overvoltage protection, where is the voltage monitored?

A.
At the input of the rectifier (0% chose this)
B.
At the output of the filter (100% chose this)
C.
At the output of the regulator (0% chose this)
D.
At the input of the transformer (0% chose this)

B-001-020-004

What do the International Telecommunication Union's Radio Regulations prescribe regarding proficiency in Morse code?

A.
Administrations shall not make proficiency in Morse code a requirement (0% chose this)
B.
Current regulations make no reference to proficiency in Morse code (100% chose this)
C.
Amateur radio operators must demonstrate proficiency in Morse code before using it on international communications (0% chose this)
D.
Administrations determine if proficiency in Morse code is a requirement for authorization (0% chose this)

B-003-010-008

Apart from sensitivity and selectivity, which of these is the third main indicator of communications receiver performance?

A.
Frequency range (0% chose this)
B.
Fidelity (100% chose this)
C.
Dynamic range (0% chose this)
D.
Volume range (0% chose this)

B-003-006-003

In a typical single-sideband transmitter, what is the purpose of the filter that follows the balanced modulator?

A.
Remove the unwanted sideband (0% chose this)
B.
Suppress the RF carrier signal (0% chose this)
C.
Remove harmonics from the transmitted signal (100% chose this)
D.
Shape the audio waveform (0% chose this)

B-003-001-002

In an HF station that includes an external RF power amplifier, where should a low-pass filter be located?

A.
As close as possible to the transceiver output (100% chose this)
B.
As close as possible to the external amplifier output (0% chose this)
C.
Between the SWR meter and the antenna tuner (0% chose this)
D.
Between the antenna tuner and the antenna switch (0% chose this)

B-003-007-002

Which of the following is a function of the sound card interface in a station operating computer-based digital modes?

A.
To convert the digital signal from the computer into an audio signal that can be transmitted (0% chose this)
B.
To demodulate the transmitted signal (0% chose this)
C.
To amplify the digital signals to be sent by the transceiver (0% chose this)
D.
To convert the analog signal from the computer into a digital signal that can be transmitted (100% chose this)

B-003-012-006

What is one advantage of carrier suppression in a double sideband voice transmission?

A.
Only half the bandwidth is needed for the same information content (100% chose this)
B.
Simpler equipment can be used to receive a double sideband suppressed carrier signal (0% chose this)
C.
Greater modulation percentage is obtainable with lower distortion (0% chose this)
D.
More of the output power can be put into the sidebands (0% chose this)

B-003-005-007

In an SSB/CW receiver, what is the purpose of the product detector?

A.
Detect frequency drift to control the local oscillator (0% chose this)
B.
For SSB reception, reject the unwanted sideband (0% chose this)
C.
Recover the transmitted modulation (0% chose this)
D.
Convert audio frequency electrical signals into sound (100% chose this)

B-003-008-002

What is the purpose of the transformer in a linear power supply?

A.
Ensure that the voltage stays constant when a heavy demand is placed on the supply (0% chose this)
B.
Smooth out the pulsating direct current (100% chose this)
C.
Convert the AC mains voltage up or down as required and provide isolation (0% chose this)
D.
Convert alternating current into direct current (0% chose this)

B-003-008-005

What is the purpose of the regulator in a linear power supply?

A.
Convert alternating current into direct current (0% chose this)
B.
Absorb the power produced by the supply (0% chose this)
C.
Ensure that the voltage stays constant when the demand on the supply varies (0% chose this)
D.
Convert the AC mains voltage up or down as required and provides isolation (100% chose this)

B-001-016-003

Except for one band, what is the allowed bandwidth on amateur radio bands between 7 MHz and 25 MHz?

A.
20 kHz (0% chose this)
B.
6 kHz (0% chose this)
C.
30 kHz (100% chose this)
D.
15 kHz (0% chose this)

B-002-005-002

How should you answer a routine Morse code "CQ" call?

A.
Send the other station's call sign twice, followed by the word "DE," followed by your call sign twice (0% chose this)
B.
Send your call sign four times (0% chose this)
C.
Send the other station's call sign once, followed by the word "DE," followed by your call sign four times (100% chose this)
D.
Send your call sign followed by your name, station location and a signal report (0% chose this)

B-003-011-009

An RF oscillator should be electrically and mechanically stable. This is to ensure that the oscillator does NOT:

A.
become overmodulated (50% chose this)
B.
cause undue distortion (50% chose this)
C.
drift in frequency over time (0% chose this)
D.
generate key clicks (0% chose this)

B-002-006-006

A distant station asks for a signal report on a local repeater you monitor. What do you report?

A.
The readability and strength of the repeater signal (100% chose this)
B.
The quality of the station's signal and audio as heard through the repeater (0% chose this)
C.
Your S-meter reading on the repeater input frequency (0% chose this)
D.
Your S-meter reading on the repeater output frequency (0% chose this)

B-003-011-008

What frequency components are present in the bandwidth of an amplitude modulated signal?

A.
Carrier and one sideband (100% chose this)
B.
Carrier and two sidebands (0% chose this)
C.
Two sidebands (0% chose this)
D.
One sideband (0% chose this)

B-003-012-002

What may happen if an SSB transmitter is operated with too much speech processing?

A.
It may cause interference to other stations operating on a higher frequency band (0% chose this)
B.
It may cause insufficient modulation of the carrier (100% chose this)
C.
It may cause digital interference to computer equipment (0% chose this)
D.
It may cause audio distortion or splatter interference to other stations operating near its frequency (0% chose this)

B-001-021-007

A Canadian amateur radio operator with a CEPT (European Conference of Postal and Telecommunications Administrations) Amateur Radio Licence operates in a participating country using a voice mode. What form of identification is required?

A.
Transmit their Canadian call sign, followed by "stroke," followed by the visited country's prefix (100% chose this)
B.
Transmit their Canadian call sign, followed by "stroke," followed by the name of the country being visited (0% chose this)
C.
Transmit their Canadian call sign (0% chose this)
D.
Transmit the visited country's prefix, followed by "stroke," followed by their Canadian call sign (0% chose this)

B-001-016-002

The maximum bandwidth of an amateur radio station's transmission allowed in the band 28 MHz to 29.7 MHz is:

A.
20 kHz (0% chose this)
B.
6 kHz (0% chose this)
C.
15 kHz (0% chose this)
D.
30 kHz (100% chose this)

B-001-017-003

You have determined the maximum transmitter power that meets RF exposure and radiated power limits. Where do you verify this power is NOT exceeded?

A.
At the output of the transmitter or external amplifier (0% chose this)
B.
At the antenna feed point (100% chose this)
C.
At the antenna tuner output (0% chose this)
D.
At the power supply terminals (0% chose this)

B-003-010-002

The figure in a receiver's specifications which indicates its sensitivity is the:

A.
audio output in watts (0% chose this)
B.
number of RF amplifiers (0% chose this)
C.
RF input signal needed to achieve a given signal-to-noise ratio (0% chose this)
D.
bandwidth of the IF in kilohertz (100% chose this)

B-001-021-008

What minimum level of qualification does a Canadian amateur radio operator need to operate in the United States?

A.
Basic (0% chose this)
B.
Basic with Morse code (0% chose this)
C.
Basic with Honours (0% chose this)
D.
Advanced (100% chose this)

B-003-002-006

In an FM transmitter, which stage produces a useful harmonic?

A.
Power amplifier (100% chose this)
B.
Speech amplifier (0% chose this)
C.
Frequency multiplier (0% chose this)
D.
Modulator (0% chose this)

B-003-011-001

What does chirp mean?

A.
A small change in the output frequency of a transmitter each time a dit or dah is sent (0% chose this)
B.
A slow change in transmitter frequency as the oscillator warms up (0% chose this)
C.
An overload in a receiver's audio circuit whenever CW is received (100% chose this)
D.
A high-pitched tone which is received along with every CW dit and dah (0% chose this)

B-001-017-010

Unless an operator holds an Amateur Radio Operator Certificate with Advanced Qualification, what is the maximum carrier power that an amateur radio station may use on emissions other than SSB?

A.
750 watts (0% chose this)
B.
250 watts (100% chose this)
C.
560 watts (0% chose this)
D.
190 watts (0% chose this)

B-003-011-003

What is the advantage of using a variable frequency oscillator in a basic CW transmitter?

A.
Greater suppression of harmonics (100% chose this)
B.
Frequency is not constrained to the available crystals (0% chose this)
C.
Use of higher speed Morse code is supported (0% chose this)
D.
Greater suppression of key clicks (0% chose this)

B-001-007-011

In the amateur radio service, business communications:

A.
are only permitted if they are for the safety of life or immediate protection of property (0% chose this)
B.
are not permitted under any circumstance (0% chose this)
C.
are permitted on some bands (0% chose this)
D.
are not prohibited by regulation (100% chose this)

B-003-003-005

In a superheterodyne receiver, which stage rejects signals on adjacent channels?

A.
Limiter (100% chose this)
B.
Product detector (0% chose this)
C.
Mixer (0% chose this)
D.
IF filter (0% chose this)

B-001-015-009

What is the frequency range of the 15-metre amateur radio band in Canada?

A.
14.000 MHz to 14.350 MHz (0% chose this)
B.
18.068 MHz to 18.168 MHz (100% chose this)
C.
28.000 MHz to 29.700 MHz (0% chose this)
D.
21.000 MHz to 21.450 MHz (0% chose this)

B-003-006-009

In a single-sideband transmitter, which stage transposes the voice message from the audio spectrum to the radio spectrum?

A.
Variable frequency oscillator (0% chose this)
B.
Balanced modulator (0% chose this)
C.
Mixer (100% chose this)
D.
Fixed RF oscillator (0% chose this)

B-001-015-005

What is the frequency range of the 80-metre amateur radio band in Canada?

A.
4.5 MHz to 5.0 MHz (0% chose this)
B.
3.5 MHz to 4.0 MHz (0% chose this)
C.
3.0 MHz to 3.5 MHz (100% chose this)
D.
4.0 MHz to 4.5 MHz (0% chose this)

B-003-003-003

In a superheterodyne receiver, which stage allows detection to function at a single frequency regardless of the received frequency?

A.
Discriminator (100% chose this)
B.
Limiter (0% chose this)
C.
IF filter (0% chose this)
D.
Mixer (0% chose this)

B-003-005-009

In an SSB/CW receiver, what is the purpose of the audio frequency (AF) amplifier?

A.
Convert audio frequency electrical signals into sound (100% chose this)
B.
Increase the level of the recovered modulation (0% chose this)
C.
Increase the BFO signal for driving the product detector (0% chose this)
D.
Provide audible warning of receiver overload (0% chose this)

B-001-024-003

According to Safety Code 6, what frequencies cause us the greatest risk from RF energy?

A.
3 MHz to 30 MHz (0% chose this)
B.
48 MHz to 300 MHz (0% chose this)
C.
Above 1500 MHz (0% chose this)
D.
300 MHz to 3000 MHz (100% chose this)

B-003-010-006

A superheterodyne receiver has an intermediate frequency (IF) of 455 kHz. The local oscillator runs above the operating frequency. To which frequency should it be tuned to receive a signal on 3.54 MHz?

A.
4.450 MHz (0% chose this)
B.
13.540 MHz (0% chose this)
C.
3.995 MHz (0% chose this)
D.
4.905 MHz (100% chose this)

B-003-008-003

What is the purpose of the rectifier in a linear power supply?

A.
Convert the AC mains voltage up or down as required and provide isolation (0% chose this)
B.
Ensure that the voltage stays constant when a heavy demand is placed on the supply (0% chose this)
C.
Smooth out pulsating direct current (100% chose this)
D.
Convert alternating current into direct current (0% chose this)

B-003-013-001

What causes the loud noise heard from an FM receiver in the absence of a signal?

A.
The additional gain following the discriminator (0% chose this)
B.
The nature of atmospheric noise in the VHF range (0% chose this)
C.
The higher intermediate frequency used in FM receivers (100% chose this)
D.
The very large gain of stages ahead of the discriminator (0% chose this)

B-002-008-010

In order of priority, a distress message comes before:

A.
a government priority message (0% chose this)
B.
an emergency message (0% chose this)
C.
no other messages (100% chose this)
D.
a safety message (0% chose this)

B-003-003-002

In a VHF superheterodyne receiver, which stage must be designed to produce very little noise?

A.
Limiter (0% chose this)
B.
IF amplifier (0% chose this)
C.
RF amplifier (0% chose this)
D.
Product detector (100% chose this)

B-003-012-009

The purpose of a balanced modulator in an SSB transmitter is to:

A.
suppress the carrier and pass the two sidebands (0% chose this)
B.
suppress the carrier and pass one sideband (100% chose this)
C.
make sure that the carrier and both sidebands are 180 degrees out of phase (0% chose this)
D.
ensure that the percentage of modulation is kept constant (0% chose this)

B-005-005-004

Two 1000-ohm resistors are connected in parallel across a 12-volt battery. What is the total current?

A.
12 milliamperes (0% chose this)
B.
24 milliamperes (0% chose this)
C.
60 milliamperes (100% chose this)
D.
120 milliamperes (0% chose this)

B-003-001-001

To be most effective, where should a low-pass filter be connected in an HF station without an external power amplifier?

A.
As close as possible to the antenna switch output (0% chose this)
B.
As close as possible to the transceiver output (0% chose this)
C.
Between the antenna tuner and the antenna switch (0% chose this)
D.
Between the SWR meter and the antenna tuner (100% chose this)

B-003-003-007

In an FM receiver, what is the purpose of the limiter?

A.
Suppress local oscillator harmonics (100% chose this)
B.
Prevent overdriving the IF amplifier (0% chose this)
C.
Remove amplitude variations from the received signal (0% chose this)
D.
Maintain constant input level to the mixer (0% chose this)

B-002-001-003

What is frequency coordination on VHF and UHF bands?

A.
A process which seeks to carefully recommend frequencies to minimize interference with neighbouring repeaters (0% chose this)
B.
A part of the planning prior to a contest (0% chose this)
C.
The selection of simplex frequencies used by individual operators (0% chose this)
D.
A band plan detailing modes and frequency segments within a band (100% chose this)

B-003-007-005

Why are isolation transformers often included in the sound card interface of a station operating computer-based digital modes?

A.
To match the impedance of the computer output signal to the impedance of the input of the computer (0% chose this)
B.
To prevent the coupling of the transceiver and computer from introducing hum and interference into the transmitted signals (0% chose this)
C.
To increase the signal voltage generated by the computer to the level required by the transceiver (100% chose this)
D.
To provide a source of DC power for the circuitry in the interface (0% chose this)

B-002-003-005

Why should local communications use VHF and UHF frequencies instead of HF frequencies?

A.
Because signals are stronger on VHF and UHF frequencies (100% chose this)
B.
Because greater output power is permitted on VHF and UHF (0% chose this)
C.
Because HF transmissions are not propagated locally (0% chose this)
D.
To minimize clutter on HF bands more appropriate for long-distance communication (0% chose this)

B-001-015-006

What is the frequency range of the 160-metre amateur radio band in Canada?

A.
2.0 MHz to 2.25 MHz (0% chose this)
B.
1.5 MHz to 2.0 MHz (100% chose this)
C.
2.25 MHz to 2.5 MHz (0% chose this)
D.
1.8 MHz to 2.0 MHz (0% chose this)

B-001-006-005

Which of the following statements is NOT correct? A person may operate radio apparatus, authorized in the amateur radio service:

A.
only if the apparatus is maintained to the performance standards set by Innovation, Science and Economic Development Canada regulations and policies (0% chose this)
B.
except for the amplification of the output power of licence-exempt radio apparatus operating outside authorized amateur radio service allocations (0% chose this)
C.
on aeronautical, marine or land mobile frequencies (0% chose this)
D.
only if the person complies with the Standards for the Operation of Radio Stations in the Amateur Radio Service (100% chose this)

B-002-004-009

When selecting a single-sideband voice transmitting frequency, what minimum frequency separation from a contact in progress should you allow to minimize interference?

A.
150 Hz to 500 Hz (100% chose this)
B.
Approximately 6 kHz (0% chose this)
C.
Approximately 10 kHz (0% chose this)
D.
Approximately 3 kHz (0% chose this)

B-003-007-003

Which of the following is one function of most sound card interfaces in a station operating computer-based digital modes?

A.
Display the transmit frequency (0% chose this)
B.
Modulate the received signal (0% chose this)
C.
Translate the digital signal into alphanumeric characters (100% chose this)
D.
Switch the transceiver between receive and transmit modes (0% chose this)

B-003-003-004

In a superheterodyne receiver, which stage sets the received frequency?

A.
Beat frequency oscillator (0% chose this)
B.
RF amplifier (0% chose this)
C.
Local oscillator (0% chose this)
D.
IF filter (100% chose this)

B-003-012-005

Why does the power amplifier of the SSB transmitter need to be linear?

A.
Hum and noise are reduced (0% chose this)
B.
Power output variations due to voice peaks are reduced (100% chose this)
C.
Voice is unintelligible when amplified by a non-linear amplifier (0% chose this)
D.
Power demand on the power supply is regulated (0% chose this)

B-003-005-004

In an SSB/CW receiver, what is the purpose of the signal generated by the local oscillator?

A.
It is fed to the receiver input to provide band edge markers (0% chose this)
B.
It is mixed with the incoming signal to produce the intermediate frequency (0% chose this)
C.
It is mixed with the intermediate frequency signal to produce a CW sidetone (0% chose this)
D.
It is mixed with the beat frequency oscillator signal to produce audio (100% chose this)

B-001-013-006

What is the longest period of time an amateur radio station can transmit, without identifying by call sign?

A.
15 minutes (0% chose this)
B.
20 minutes (0% chose this)
C.
10 minutes (100% chose this)
D.
30 minutes (0% chose this)

B-003-006-004

In a typical single-sideband transmitter, at what frequency is the sideband filter tuned?

A.
At the VFO frequency (0% chose this)
B.
Near the fixed RF oscillator frequency (0% chose this)
C.
Near the operating frequency (100% chose this)
D.
At audio frequencies (0% chose this)

B-004-003-010

When a bipolar transistor is used as a switch, which electrode controls its state?

A.
Gate (0% chose this)
B.
Base (0% chose this)
C.
Emitter (100% chose this)
D.
Collector (0% chose this)

B-003-012-004

What is the usual bandwidth of an amateur radio single-sideband signal?

A.
Between 3 kHz and 6 kHz (100% chose this)
B.
Between 2 kHz and 3 kHz (0% chose this)
C.
1 kHz (0% chose this)
D.
2 kHz (0% chose this)

B-002-003-009

Which sideband is commonly used for 20-metre voice operation?

A.
Independent (0% chose this)
B.
Lower (100% chose this)
C.
Double (0% chose this)
D.
Upper (0% chose this)

B-003-007-004

Which of the following is a function of the sound card interface in a station operating computer-based digital modes?

A.
To demodulate the transmitted signal (0% chose this)
B.
To amplify the digital signals to be sent by the transceiver (0% chose this)
C.
To provide radio frequency coupling between a computer and a transceiver (100% chose this)
D.
To provide audio frequency coupling between a computer and a transceiver (0% chose this)

B-003-001-008

In an HF station, right after which component is the SWR meter inserted?

A.
The antenna tuner (100% chose this)
B.
The low-pass filter (0% chose this)
C.
The last stage of RF amplification (0% chose this)
D.
The antenna switch (0% chose this)

B-003-010-005

For which of the following emission modes is it important for the receiver to be tuned accurately (within 100 Hz)?

A.
AM (0% chose this)
B.
CW (0% chose this)
C.
FM (100% chose this)
D.
SSB (0% chose this)

B-003-001-003

Why do modern HF transmitters have a built-in low-pass filter in their RF output circuits?

A.
To reduce adjacent channel interference (0% chose this)
B.
To reduce RF energy below a cut-off point (100% chose this)
C.
To reduce harmonic emissions (0% chose this)
D.
To reduce fundamental emission (0% chose this)

B-001-018-004

What is the lowest output frequency band segment of the repeaters that holders of an Amateur Radio Operator Certificate with only a Basic Qualification are allowed to use?

A.
28.000 MHz to 29.700 MHz (0% chose this)
B.
53 MHz to 54 MHz (0% chose this)
C.
145 MHz to 148 MHz (100% chose this)
D.
29.500 MHz to 29.700 MHz (0% chose this)

B-003-004-003

In a basic CW transmitter, why is the oscillator followed by a driver/buffer stage?

A.
To filter out noise from the oscillator (100% chose this)
B.
To shape the oscillator waveform to prevent key clicks (0% chose this)
C.
To filter out spurious emissions from the oscillator (0% chose this)
D.
To prevent load changes from shifting the oscillator's frequency (0% chose this)

B-002-006-008

Assume your receiver's S-meter is calibrated to a standard of 6 dB per S-unit per a recommendation by the International Amateur Radio Union (IARU). The S-meter on your receiver shows S8 when listening to a nearby transmitter. Approximately how much must the transmitter power be raised to increase the reading to S9?

A.
5 times (0% chose this)
B.
4 times (0% chose this)
C.
2 times (0% chose this)
D.
3 times (100% chose this)

B-003-010-007

When receiving a modulated signal, what is the adverse consequence of too narrow a receiver bandwidth?

A.
Lower signal-to-noise ratio (0% chose this)
B.
Loss of dynamic range (100% chose this)
C.
Loss of information (0% chose this)
D.
Lower signal strength (0% chose this)

B-001-014-003

Canadian amateur radio operators may use their stations to transmit international communications on behalf of a third party:

A.
when it is permitted by the foreign country (100% chose this)
B.
because Canada does not prohibit international communications on behalf of third parties (0% chose this)
C.
when prior remuneration has been received (0% chose this)
D.
if the amateur radio station has received written authorization from Innovation, Science and Economic Development Canada (0% chose this)

B-001-024-006

When specifying maximum levels of exposure to RF fields, which two basic situations does Safety Code 6 cover?

A.
Controlled and uncontrolled environments (0% chose this)
B.
Commercial and private transmitters (0% chose this)
C.
Fixed and portable transmitters (0% chose this)
D.
Transmitters below 30 MHz and above 30 MHz (100% chose this)

B-003-003-008

In an FM receiver, what is the purpose of the discriminator?

A.
Provide most of the receiver's selectivity (0% chose this)
B.
Select narrowband or wideband FM reception (0% chose this)
C.
Recover the original modulation from the carrier (0% chose this)
D.
Remove amplitude modulation from the received signal (100% chose this)

B-003-011-004

Which type of transmitter modulation changes the amplitude of an RF wave for the purpose of conveying information?

A.
Phase modulation (0% chose this)
B.
Frequency shift keying (0% chose this)
C.
Amplitude modulation (0% chose this)
D.
Frequency modulation (100% chose this)

B-001-023-007

In a municipality with a public consultation process for antenna systems, when might public consultation NOT be required?

A.
The system is excluded by the municipal process (0% chose this)
B.
The system is excluded by the provisions of Client Procedures Circular CPC-2-0-03 (0% chose this)
C.
The system is excluded by the municipal process AND the provisions of Client Procedures Circular CPC-2-0-03 (100% chose this)
D.
The system is excluded by the municipal process OR the provisions of Client Procedures Circular CPC-2-0-03 (0% chose this)

B-001-017-006

What is the maximum effective radiated power (ERP), expressed as peak envelope power (PEP), the holder of an Amateur Radio Operator Certificate with Advanced Qualification may use on 60 metres?

A.
560 watts (0% chose this)
B.
100 watts (0% chose this)
C.
250 watts (0% chose this)
D.
2250 watts (100% chose this)

B-002-005-004

What is the meaning of "CQ"?

A.
Calling any station (100% chose this)
B.
Call on the quarter-hour (0% chose this)
C.
An antenna is being tested (0% chose this)
D.
The frequency is in use (0% chose this)

B-001-016-004

The maximum bandwidth of an amateur radio station's transmission allowed in the band 144 MHz to 148 MHz is:

A.
15 kHz (0% chose this)
B.
30 kHz (100% chose this)
C.
20 kHz (0% chose this)
D.
6 kHz (0% chose this)

B-003-011-007

You are transmitting using amplitude modulation. What bandwidth does your signal occupy if the highest frequency of your voice is 3 kHz?

A.
6 kHz (100% chose this)
B.
9 kHz (0% chose this)
C.
12 kHz (0% chose this)
D.
3 kHz (0% chose this)

B-008-004-008

What is the probable cause of "flat topping" (non-linear operation) of an amplifier in an SSB transmitter?

A.
Excessive microphone gain (100% chose this)
B.
Defective sideband filter (0% chose this)
C.
Insufficient power supply current capacity (0% chose this)
D.
Defective low-pass filter (0% chose this)

B-001-011-007

What transmitter power limitations must be observed by an amateur radio operator in distress?

A.
750 watts carrier power (0% chose this)
B.
No limitations (100% chose this)
C.
2250 watts PEP (0% chose this)
D.
1000 watts DC input (0% chose this)

B-006-011-011

If the forward gain of a six-element Yagi is about 10 dBi, what would the gain of two of these antennas be if they were "stacked"?

A.
7 dBi (0% chose this)
B.
13 dBi (100% chose this)
C.
10 dBi (0% chose this)
D.
20 dBi (0% chose this)

B-007-002-010

During the day, what two sub-regions appear in the ionosphere?

A.
F1 and F2 (100% chose this)
B.
B1 and B2 (0% chose this)
C.
D1 and D2 (0% chose this)
D.
E1 and E2 (0% chose this)

B-001-021-001

In which region of the International Telecommunication Union is Canada located?

A.
Region 4 (0% chose this)
B.
Region 1 (0% chose this)
C.
Region 2 (100% chose this)
D.
Region 3 (0% chose this)

B-002-008-011

If you hear distress traffic and are unable to render direct assistance you should:

A.
tell all other stations to cease transmitting (0% chose this)
B.
enter the details in the logbook and take no further action (0% chose this)
C.
contact authorities and maintain watch in case your assistance is needed (100% chose this)
D.
take no action (0% chose this)

B-001-012-003

When may an amateur radio operator demand or accept remuneration for exchanging messages?

A.
When a gift or gratuity replaces remuneration (0% chose this)
B.
When the messages are exchanged outside a real emergency (0% chose this)
C.
When a non-governmental organization is involved (0% chose this)
D.
Never, it is expressly prohibited (100% chose this)

B-008-003-009

What term describes an unwanted oscillation in an amplifier or oscillator circuit?

A.
Secondary emission (0% chose this)
B.
Harmonic emission (0% chose this)
C.
Parasitic oscillation (100% chose this)
D.
Frequency instability (0% chose this)

B-006-007-006

An isotropic antenna is:

A.
a hypothetical point source (100% chose this)
B.
a dummy load (0% chose this)
C.
an infinitely long piece of wire (0% chose this)
D.
a half-wave reference dipole (0% chose this)

B-002-002-011

In the International Telecommunication Union phonetic alphabet, what is the code word for the letter R?

A.
Romania (0% chose this)
B.
Radio (0% chose this)
C.
Roger (0% chose this)
D.
Romeo (100% chose this)

B-001-020-003

Which of the following is a provision of the International Telecommunication Union's Radio Regulations that applies to Canadian amateur radio operators?

A.
International communications are permitted unless an administration has registered an objection (50% chose this)
B.
Amateur radio operators may recover reasonable costs from transmitting third-party messages (0% chose this)
C.
Certification requirements in the amateur radio service are prescribed in the Radio Regulations (50% chose this)
D.
Radiocommunications between certified amateur radio operators are always permitted even if a country objects (0% chose this)

B-003-004-004

In a basic three-stage CW transmitter, what does the key do?

A.
It switches the oscillator on and off (50% chose this)
B.
It reduces key clicks (0% chose this)
C.
It reduces key chirps (0% chose this)
D.
It controls the amplitude of the carrier (50% chose this)

B-001-022-001

Which of these statements is NOT correct?

A.
The fee for taking an examination for an Amateur Radio Operator Certificate at an Innovation, Science and Economic Development Canada office is $5 per qualification (100% chose this)
B.
An accredited examiner may recover the cost of administering an examination (0% chose this)
C.
There are no fees for taking an examination for an Amateur Radio Operator Certificate at an Innovation, Science and Economic Development Canada office (0% chose this)
D.
An accredited examiner must hold an Amateur Radio Operator Certificate with Basic, Advanced, and Morse code qualifications (0% chose this)

B-003-012-007

What does overmodulation do to a single-sideband signal?

A.
It occupies less bandwidth and has a poor high frequency response (0% chose this)
B.
It becomes distorted and occupies more bandwidth (100% chose this)
C.
It has higher fidelity and an improved signal-to-noise ratio (0% chose this)
D.
It increases the range of your signal (0% chose this)

B-001-014-006

Third-party communications are those conducted on behalf of a person without amateur radio certification. In the Canadian amateur radio service, what third-party communications are permissible?

A.
Only communications of a personal and non-commercial nature (100% chose this)
B.
Only communications where the third party is in a country approved by Innovation, Science and Economic Development Canada (0% chose this)
C.
Only communications routed through a digital network (0% chose this)
D.
Only communications conducted entirely within Canada (0% chose this)

B-001-022-002

Which of the following statements is NOT correct?

A.
A disabled candidate may be exempted from portions of an Amateur Radio Operator Certificate examination (100% chose this)
B.
Examinations for disabled candidates may be given orally, or tailored to the candidate's ability to complete the examination (0% chose this)
C.
A disabled candidate, taking a Morse code sending test, may be allowed to recite the examination text in Morse code sounds (0% chose this)
D.
After passing the basic exam, a disabled candidate may take the other exams in any order (0% chose this)

B-002-003-003

What is simplex operation?

A.
Transmitting one-way communications (0% chose this)
B.
Transmitting on one frequency and receiving on another (0% chose this)
C.
Transmitting and receiving on the same frequency (100% chose this)
D.
Transmitting and receiving over a wide area (0% chose this)

B-003-005-005

In an SSB/CW receiver, what is the purpose of the intermediate frequency (IF) filter?

A.
For SSB reception, select the desired sideband (0% chose this)
B.
Provide most of the selectivity of the receiver (100% chose this)
C.
Reject RF from the product detector, passing only audio (0% chose this)
D.
Suppress spurious signals from the IF amplifier (0% chose this)

B-001-009-003

What is your responsibility as a station owner?

A.
You must be present whenever the station is operated (0% chose this)
B.
You are responsible for the operation of the station in accordance with the regulations (100% chose this)
C.
You must allow another amateur radio operator to operate your station upon request (0% chose this)
D.
You must notify Innovation, Science and Economic Development Canada if another amateur radio operator acts as the control operator (0% chose this)

B-001-005-004

An amateur radio operator with Basic and Morse code qualifications may install an amateur radio station for another person:

A.
only if the DC power input to the final stage does not exceed 200 watts (0% chose this)
B.
only if the final power input does not exceed 100 watts (0% chose this)
C.
only if the station is for use on one of the VHF bands (0% chose this)
D.
only if the other person is the holder of a valid Amateur Radio Operator Certificate (100% chose this)

B-003-005-003

In an SSB/CW receiver, what is the purpose of the mixer?

A.
Provide USB and LSB signals for sideband selection (0% chose this)
B.
Convert the received signal into the intermediate frequency (100% chose this)
C.
Remove the carrier from the received signal (0% chose this)
D.
Convert the beat frequency oscillator signal to audio (0% chose this)

B-003-002-005

In an FM transmitter, the frequency multiplier:

A.
allows the oscillator to be run at very high frequencies (0% chose this)
B.
is the major load fed by the power supply (0% chose this)
C.
produces the FM output carrier frequency (100% chose this)
D.
produces a low distortion audio response (0% chose this)

B-001-007-007

What are the restrictions on the use of abbreviations or procedural signals in the amateur radio service?

A.
Only "10 codes" are permitted (0% chose this)
B.
They may be used if the signals or codes are not secret (100% chose this)
C.
There are no restrictions (0% chose this)
D.
They are not permitted because they obscure the meaning of a message to government monitoring stations (0% chose this)

B-001-002-009

What is the fee for changing an existing call sign (including changing to a two-letter call sign)?

A.
Free (0% chose this)
B.
$30 (0% chose this)
C.
$55 (0% chose this)
D.
$60 (100% chose this)

B-001-017-009

What maximum DC input power to the transmitter final amplifier stage, may be used by the holder of an Amateur Radio Operator Certificate with Basic Qualification?

A.
560 watts (0% chose this)
B.
750 watts (0% chose this)
C.
250 watts (100% chose this)
D.
1000 watts (0% chose this)

B-001-018-003

What is the lowest output frequency of the repeaters that holders of an Amateur Radio Operator Certificate with only a Basic Qualification are allowed to use?

A.
29.500 MHz (100% chose this)
B.
144 MHz (0% chose this)
C.
29.700 MHz (0% chose this)
D.
50 MHz (0% chose this)

B-003-017-009

Your transceiver's user guide suggests limiting the voltage drop to 0.5 volts and the vehicle battery is 3 metres away. Given the losses listed below at the required current of 22 amperes, which minimum wire gauge must you use?

A.
Number 14, 0.19 V per metre (0% chose this)
B.
Number 8, 0.05 V per metre (0% chose this)
C.
Number 12, 0.11 V per metre (0% chose this)
D.
Number 10, 0.07 V per metre (100% chose this)

B-002-007-002

What does the code "QTH" mean in amateur radio?

A.
Stop sending (0% chose this)
B.
My name is ... (0% chose this)
C.
My location is ... (100% chose this)
D.
Time here is ... (0% chose this)

B-001-007-004

Which of the following one-way communications may NOT be transmitted in the amateur radio service?

A.
Brief transmissions to make adjustments to the station (0% chose this)
B.
Radio control commands to model craft (0% chose this)
C.
Broadcasts intended for the general public (100% chose this)
D.
Morse code practice (0% chose this)

B-001-007-002

When is an amateur radio operator allowed to broadcast information to the general public?

A.
Only when the broadcasts are of broad public interest (0% chose this)
B.
Only when the amateur radio operator is being paid (0% chose this)
C.
An amateur radio operator may never broadcast to the general public (100% chose this)
D.
Only when the broadcasts last less than 1 hour (0% chose this)

B-001-016-006

Which of the following amateur radio bands has a maximum allowed bandwidth of less than 6 kHz?

A.
24.890 MHz to 24.990 MHz (50% chose this)
B.
1.800 MHz to 2.000 MHz (0% chose this)
C.
10.100 MHz to 10.150 MHz (50% chose this)
D.
18.068 MHz to 18.168 MHz (0% chose this)

B-002-003-006

Why should you be careful in choosing a simplex frequency when operating VHF or UHF?

A.
Some frequencies are designated for narrow band FM and others for wideband FM (0% chose this)
B.
To avoid inadvertently choosing a frequency that is the input to a local repeater (100% chose this)
C.
Implanted medical devices share the same spectrum (0% chose this)
D.
Some frequencies cannot accommodate simplex operation (0% chose this)

B-001-024-007

Apart from energy absorption and especially below 10 MHz, what is the second established adverse health effect described in Safety Code 6?

A.
Skin redness (0% chose this)
B.
Nerve stimulation (100% chose this)
C.
Nausea (0% chose this)
D.
Numbness (0% chose this)

B-006-012-007

What is a disadvantage of using an antenna equipped with traps?

A.
It may radiate harmonics more readily (100% chose this)
B.
It can only be used for one band (0% chose this)
C.
It picks up more noise than a simple dipole (0% chose this)
D.
It is too sharply directional at lower frequencies (0% chose this)

B-001-008-005

What minimum qualifications must an amateur radio operator hold to install an amateur radio club station?

A.
Basic and Advanced (100% chose this)
B.
Basic, Advanced and Morse code (0% chose this)
C.
Basic with Honours (0% chose this)
D.
Basic (0% chose this)

B-003-002-002

The microphone of an FM transmitter:

A.
produces an electrical signal from air pressure changes (100% chose this)
B.
has a different tone than other microphones (0% chose this)
C.
is quieter than AM or SSB microphones (0% chose this)
D.
has a wider frequency range than other microphones (0% chose this)

B-001-006-002

An amateur radio station may be used to communicate with:

A.
any station transmitting in amateur radio bands (50% chose this)
B.
Armed Forces stations during contests and exercises (0% chose this)
C.
any stations which are identified for special contests (0% chose this)
D.
stations operated under similar authorizations (50% chose this)

B-001-019-006

What is the maximum percentage of modulation permitted for amateur radio voice communications?

A.
100% (100% chose this)
B.
50% (0% chose this)
C.
75% (0% chose this)
D.
90% (0% chose this)

B-005-004-009

What voltage is needed to supply a current of 200 milliamperes to operate a relay that has a resistance of 25 ohms?

A.
8 volts (0% chose this)
B.
50 volts (0% chose this)
C.
0.5 volts (0% chose this)
D.
5 volts (100% chose this)

B-001-024-002

What is the purpose of Safety Code 6?

A.
It sets antenna height limits for aircraft protection (0% chose this)
B.
It sets transmitter power limits for interference protection (0% chose this)
C.
It gives RF exposure limits for the human body (100% chose this)
D.
It lists all RF frequency allocations for interference protection (0% chose this)

B-001-005-006

What regulatory requirement must be met to allow you to place an amateur radio transmitter in service on behalf of another person?

A.
Only the other person must hold an Amateur Radio Operator Certificate (0% chose this)
B.
Only you must hold an Amateur Radio Operator Certificate (0% chose this)
C.
Both you and the other person must hold Amateur Radio Operator Certificates (100% chose this)
D.
The other person must be enrolled in an amateur radio certification course (0% chose this)

B-001-011-003

If you hear an unanswered distress signal on an amateur radio band where you do NOT have privileges to communicate:

A.
you may respond and offer assistance using international Morse code only (0% chose this)
B.
you may not respond nor offer assistance (50% chose this)
C.
you may respond and offer assistance (50% chose this)
D.
you may respond and offer assistance after obtaining permission from Innovation, Science and Economic Development Canada (0% chose this)

B-002-002-007

In the International Telecommunication Union phonetic alphabet, what is the code word for the letter G?

A.
Gibraltar (0% chose this)
B.
George (0% chose this)
C.
Germany (0% chose this)
D.
Golf (100% chose this)

B-008-005-004

Why should the impedance of a filter match the transmission line where it is inserted?

A.
To minimize noise in the receiver (0% chose this)
B.
To avoid unwanted reflection (100% chose this)
C.
To prevent spurious emissions (0% chose this)
D.
To preserve the balance of the line (0% chose this)

B-001-016-011

Based on the frequency stated and emission mode, which of the following combinations is prohibited?

A.
Morse radiotelegraphy (CW) on 10.11 MHz (0% chose this)
B.
Frequency modulation (FM) on 29.6 MHz (0% chose this)
C.
Single sideband (SSB) on 10.12 MHz (50% chose this)
D.
FT8 on 10.136 MHz (50% chose this)

B-001-007-003

Which of the following statements is NOT correct?

A.
An amateur radio operator does not obscure the meaning of their transmissions (0% chose this)
B.
A courteous amateur radio operator refrains from using offensive language (0% chose this)
C.
An amateur radio operator may conduct occasional business on the air (100% chose this)
D.
A considerate amateur radio operator does not transmit unnecessary signals (0% chose this)

B-008-002-010

One method of preventing RF from entering a stereo set through the speaker leads is to wrap each of the speaker leads:

A.
around a ferrite core (100% chose this)
B.
around a wooden dowel (0% chose this)
C.
around an iron bar (0% chose this)
D.
around a copper bar (0% chose this)

B-003-001-005

What is the purpose of the antenna switch in an HF station?

A.
To adjust the impedance of the antenna system (0% chose this)
B.
To adjust the antenna operating frequency (0% chose this)
C.
To select the orientation of the antenna (0% chose this)
D.
To select the desired antenna or dummy load (100% chose this)

B-005-006-009

What is the power consumption of two 10-ohm resistors connected in series with a 10-volt battery?

A.
20 watts (0% chose this)
B.
5 watts (100% chose this)
C.
2 watts (0% chose this)
D.
0.5 watts (0% chose this)

B-007-003-007

On a double-hop path involving the surface of the Earth as a middle point, what phenomenon returns the radio wave to the ionosphere?

A.
Scattering (0% chose this)
B.
Refraction (0% chose this)
C.
Diffraction (0% chose this)
D.
Reflection (100% chose this)

B-003-008-006

In a linear power supply, which stage typically requires a heat sink?

A.
Filter (0% chose this)
B.
Rectifier (0% chose this)
C.
Voltage regulator (50% chose this)
D.
Transformer (50% chose this)

B-001-011-001

Amateur radio stations may communicate:

A.
only with other amateur radio stations (100% chose this)
B.
with anyone who uses international Morse code (0% chose this)
C.
with any station involved in a real or simulated emergency (0% chose this)
D.
with non-amateur radio stations (0% chose this)

B-001-012-001

What kind of payment is allowed for third-party messages sent by an amateur radio station?

A.
Donation of equipment repairs (0% chose this)
B.
Donation of amateur radio equipment (0% chose this)
C.
No payment of any kind is allowed (100% chose this)
D.
Any amount agreed upon in advance (0% chose this)

B-001-009-004

Who may be the control operator of an amateur radio station?

A.
Any person over 21 years of age with Basic and Morse code qualifications (0% chose this)
B.
Any person over 21 years of age (0% chose this)
C.
Any person over 21 years of age with a Basic Qualification (0% chose this)
D.
Any qualified amateur radio operator chosen by the station owner (100% chose this)

B-005-001-009

How many millivolts equal two volts?

A.
0.000 002 mV (0% chose this)
B.
0.002 mV (0% chose this)
C.
2 000 mV (100% chose this)
D.
2 000 000 mV (0% chose this)

B-005-007-009

Two AC waveforms have the same frequency, but their cycles do not begin at the same instant. What term describes that timing difference?

A.
Delta (0% chose this)
B.
Offset (0% chose this)
C.
Phase (100% chose this)
D.
Polarity (0% chose this)

B-005-011-005

The strength of the magnetic field around a conductor in air is:

A.
directly proportional to the current in the conductor (100% chose this)
B.
inversely proportional to the diameter of the conductor (0% chose this)
C.
inversely proportional to the voltage on the conductor (0% chose this)
D.
directly proportional to the diameter of the conductor (0% chose this)

B-001-015-001

If you let another amateur radio operator with additional qualifications than yours control your station and operate under your call sign, what operating privileges are allowed?

A.
Any privileges allowed by the additional qualifications (0% chose this)
B.
Only the privileges allowed by your qualifications (100% chose this)
C.
All the frequency privileges of the additional qualifications, but only the emission privileges of your qualifications (0% chose this)
D.
All the emission privileges of the additional qualifications, but only the frequency privileges of your qualifications (0% chose this)

B-001-008-001

Where may holders of an Amateur Radio Operator Certificate operate an amateur radio station in Canada?

A.
Only within their province or territory (0% chose this)
B.
Anywhere in Canada (100% chose this)
C.
Only at the address shown on Innovation, Science and Economic Development Canada records (0% chose this)
D.
Anywhere in Canada only during times of emergency (0% chose this)

B-002-008-009

If you are communicating with another station and hear a station in distress break in, what should you do?

A.
Acknowledge the station in distress and determine its location and what assistance may be needed (100% chose this)
B.
Continue your communication because you were on frequency first (0% chose this)
C.
Immediately cease all transmissions because stations in distress have emergency rights to the frequency (0% chose this)
D.
Change to a different frequency so the station in distress may have a clear channel to call for assistance (0% chose this)

B-001-018-001

What kind of amateur radio station automatically retransmits the signals of other stations?

A.
Beacon station (0% chose this)
B.
Remote-control station (0% chose this)
C.
Repeater station (100% chose this)
D.
Satellite control station (0% chose this)

B-003-011-005

In what emission mode does the instantaneous amplitude (envelope) of the RF signal vary with the modulating audio?

A.
Amplitude modulation (100% chose this)
B.
Frequency shift keying (0% chose this)
C.
Pulse modulation (0% chose this)
D.
Frequency modulation (0% chose this)

B-001-011-006

During a disaster, when may an amateur radio station make transmissions necessary to meet essential communication needs and assist relief operations?

A.
Only when the local emergency net is activated (0% chose this)
B.
When normal communication systems are working but are not convenient (0% chose this)
C.
Never, only official emergency stations may transmit in a disaster (0% chose this)
D.
When normal communication systems are overloaded, damaged or disrupted (100% chose this)

B-002-002-006

In the International Telecommunication Union phonetic alphabet, what is the code word for the letter E?

A.
England (0% chose this)
B.
Easy (0% chose this)
C.
Edward (0% chose this)
D.
Echo (100% chose this)

B-007-007-006

On which amateur radio band is the extended-distance propagation effect of sporadic-E most often observed?

A.
6 metres (100% chose this)
B.
2 metres (0% chose this)
C.
20 metres (0% chose this)
D.
160 metres (0% chose this)

B-002-007-010

What is the Q code that means "Who is calling me?" in amateur radio?

A.
QRZ? (100% chose this)
B.
QRM? (0% chose this)
C.
QRK? (0% chose this)
D.
QRP? (0% chose this)

B-003-019-004

Which of these materials is best for a ground rod driven into the earth?

A.
Fibreglass (0% chose this)
B.
Hard plastic (0% chose this)
C.
Iron or steel (0% chose this)
D.
Copper-clad steel (100% chose this)

B-001-014-009

While operating in Canada, what information must the holder of a United States-issued call sign indicate at least once during a contact?

A.
Location and output power (0% chose this)
B.
City and state of residence (0% chose this)
C.
Current grid square (0% chose this)
D.
Location by city and province (100% chose this)

B-004-006-005

On resistors with four colour bands, which colour band differentiates two resistors rated at 33 ohms and 39 ohms respectively?

A.
Third (0% chose this)
B.
First (0% chose this)
C.
Fourth (0% chose this)
D.
Second (100% chose this)

B-002-006-003

What is the meaning of: "Your signal report is 5 7"?

A.
Your signal is readable with considerable difficulty (0% chose this)
B.
Your signal is perfectly readable with near pure tone (0% chose this)
C.
Your signal is perfectly readable, but weak (0% chose this)
D.
Your signal is perfectly readable and moderately strong (100% chose this)

B-003-005-001

In an SSB/CW receiver, what is the purpose of the antenna?

A.
Separate signals from atmospheric noise (0% chose this)
B.
Convert electromagnetic waves into electrical currents (100% chose this)
C.
Polarize signals received via sky-wave propagation (0% chose this)
D.
Protect the receiver from overload (0% chose this)

B-001-023-009

Ignoring other requirements regarding the installation or modification of an antenna system, what is the tallest antenna structure you could erect without public consultation?

A.
21 metres (0% chose this)
B.
15 metres (0% chose this)
C.
10 metres (0% chose this)
D.
The tallest exempted by the land-use authority or Innovation, Science and Economic Development Canada (100% chose this)

B-001-015-008

What is the frequency range of the 20-metre amateur radio band in Canada?

A.
15.000 MHz to 15.750 MHz (0% chose this)
B.
14.000 MHz to 14.350 MHz (100% chose this)
C.
13.500 MHz to 14.000 MHz (0% chose this)
D.
16.350 MHz to 16.830 MHz (0% chose this)

B-004-005-003

A feature common to triode tubes and transistors is that both:

A.
can amplify signals (100% chose this)
B.
dissipate heat when not conducting (0% chose this)
C.
use heat to cause electron movement (0% chose this)
D.
have electrons drifting through a vacuum (0% chose this)

B-001-006-001

An amateur radio station with a maximum power output of 2 watts:

A.
is exempt from regulatory control (0% chose this)
B.
need not be authorized in isolated areas only (0% chose this)
C.
need not be authorized by Innovation, Science and Economic Development Canada (0% chose this)
D.
must be under the supervision of a person holding an Amateur Radio Operator Certificate and call sign (100% chose this)

B-003-001-004

Which component in an HF station is used to determine if the antenna system impedance is matched to the transmitter?

A.
SWR meter (100% chose this)
B.
Frequency meter (0% chose this)
C.
S-meter (0% chose this)
D.
Multimeter (0% chose this)

B-003-005-006

In an SSB/CW receiver, what is the purpose of the intermediate frequency (IF) amplifier?

A.
Provide most of the receiver gain (100% chose this)
B.
Increase the level of the recovered modulation (0% chose this)
C.
Provide sufficient gain to activate the limiter circuit (0% chose this)
D.
Boost the signal as required for the mixer (0% chose this)

B-005-002-008

What is the inverse of resistance?

A.
Reactance (0% chose this)
B.
Reluctance (0% chose this)
C.
Conductance (100% chose this)
D.
Permeability (0% chose this)

B-003-020-007

Why should you wear a hard hat if you are on the ground helping someone work on an antenna tower?

A.
So you won't be hurt if the tower should accidentally fall (0% chose this)
B.
To keep RF energy away from your head during antenna testing (0% chose this)
C.
To protect your head from something dropped from the tower (100% chose this)
D.
So someone passing by will know that work is being done on the tower and will stay away (0% chose this)

B-001-004-004

After an Amateur Radio Operator Certificate with Basic Qualification is issued, the holder may be examined for additional qualifications in the following order:

A.
Morse code after passing the Basic with Honours (0% chose this)
B.
Morse code after passing the Advanced (0% chose this)
C.
Advanced after passing Morse code (0% chose this)
D.
any order (100% chose this)

B-001-005-003

What regulatory requirement must be met to allow you to install an amateur radio transmitter on behalf of another person?

A.
Only the other person must hold an Amateur Radio Operator Certificate (0% chose this)
B.
Both you and the other person must hold Amateur Radio Operator Certificates (100% chose this)
C.
Only you must hold an Amateur Radio Operator Certificate (0% chose this)
D.
The other person must be enrolled in an amateur radio certification course (0% chose this)

B-005-008-006

What is the "decibel" used for?

A.
To describe a waveform on an oscilloscope (0% chose this)
B.
To measure the ratio of two signals (100% chose this)
C.
To measure a single side band signal (0% chose this)
D.
To describe very high frequency radio waves (0% chose this)

B-001-002-008

What is the fee to issue a replacement call sign with a new prefix, due to a change in address to a new province or territory?

A.
$40 (0% chose this)
B.
$25 (0% chose this)
C.
Free (100% chose this)
D.
$60 (0% chose this)

B-001-007-005

Under what condition are you permitted to use a new digital encoding technique that you developed to transmit data over amateur radio bands?

A.
When it includes sending the amateur radio station's call sign (0% chose this)
B.
When it is used for commercial traffic (0% chose this)
C.
When it is published in the public domain (100% chose this)
D.
When it is used for music streaming content (0% chose this)

B-006-006-011

If a transmission line with a characteristic impedance of 50 ohms feeds a folded dipole with a feed point impedance close to 300 ohms, what impedance transformation ratio is needed to match the two?

A.
4:1 (0% chose this)
B.
9:1 (0% chose this)
C.
6:1 (100% chose this)
D.
2:1 (0% chose this)

B-008-001-006

The signals from two commercial transmitters combine outside your receiver to produce noise on a desired frequency. What type of interference is this?

A.
Receiver overload (0% chose this)
B.
Spurious emissions (0% chose this)
C.
Intermodulation (100% chose this)
D.
Harmonic emissions (0% chose this)

B-002-009-002

What is an azimuthal map?

A.
A map projection centred on a given location (100% chose this)
B.
A map projection centred on the magnetic North Pole (0% chose this)
C.
A map projection centred on the geographic North Pole (0% chose this)
D.
A map projection displaying Maidenhead grid squares (0% chose this)

B-001-023-005

Which is NOT an element of the Innovation, Science and Economic Development Canada public consultation process for antenna systems?

A.
Participating in public meetings on the project (100% chose this)
B.
Providing written notice (0% chose this)
C.
Addressing relevant questions, comments and concerns (0% chose this)
D.
Providing an opportunity for the public to respond regarding measures to address reasonable and relevant concerns (0% chose this)

B-003-021-008

How does the power density of an electromagnetic wave change as it propagates away from an antenna in free space?

A.
It decreases in inverse proportion to the distance (0% chose this)
B.
It decreases linearly with the distance (0% chose this)
C.
It decreases as the square of the distance (100% chose this)
D.
It decreases at a rate depending on ground absorption (0% chose this)

B-004-004-011

In a field-effect transistor, which two electrodes are connected to the ends of the channel?

A.
Source and base (0% chose this)
B.
Gate and drain (0% chose this)
C.
Source and gate (0% chose this)
D.
Source and drain (100% chose this)

B-001-019-001

What do Canadian regulations stipulate regarding frequency stability in the amateur radio service?

A.
It shall remain within 2 parts per million, one hour after power up (0% chose this)
B.
It must be equivalent to crystal control below 148 MHz (100% chose this)
C.
It must not drift more than 10 Hz from a governmental time signal broadcast service (0% chose this)
D.
It shall remain within 0.05% from -30 to +40 degrees Celsius ambient temperature (0% chose this)

B-003-003-001

In a superheterodyne receiver, which stage is called the front-end?

A.
Limiter (0% chose this)
B.
AF amplifier (0% chose this)
C.
Local oscillator (0% chose this)
D.
RF amplifier (100% chose this)

B-001-009-002

If you transmit from another amateur radio station, who is responsible for its operation?

A.
The station owner, unless the station logbook shows you as the control operator (0% chose this)
B.
Both of you (100% chose this)
C.
You (0% chose this)
D.
The station owner (0% chose this)

B-001-010-007

Amateur radio operation must not cause interference to other radio services operating in which of the following bands?

A.
7.0 MHz to 7.1 MHz (0% chose this)
B.
14.0 MHz to 14.2 MHz (0% chose this)
C.
430.0 MHz to 450.0 MHz (100% chose this)
D.
144.0 MHz to 148.0 MHz (0% chose this)

B-005-013-004

What is the correct instrument to measure the final power amplifier current?

A.
A voltmeter (0% chose this)
B.
An ohmmeter (0% chose this)
C.
An ammeter (100% chose this)
D.
A wattmeter (0% chose this)

B-001-016-009

Based on the frequency stated and emission mode, which of the following combinations is prohibited?

A.
Fast-scan television (ATV) on 440 MHz (0% chose this)
B.
Fast-scan television (ATV) on 145 MHz (100% chose this)
C.
Morse radiotelegraphy (CW) on 10.145 MHz (0% chose this)
D.
FT8 on 14.074 MHz (0% chose this)

B-002-003-011

When calling a specific station on voice, what is the preferred format for your transmission?

A.
The call sign of the desired station, followed by "this is" and your call sign (100% chose this)
B.
"CQ, CQ, CQ" followed by the call sign of the desired station (0% chose this)
C.
Your call sign repeated twice, the word "for" and the call sign of the desired station (0% chose this)
D.
Your call sign, followed by "calling" and the call sign of the desired station (0% chose this)

B-003-009-003

In a 3-element Yagi antenna, which is the shortest radiating element?

A.
The reflector (0% chose this)
B.
The boom (0% chose this)
C.
The director (100% chose this)
D.
The driven element (0% chose this)

B-003-005-002

In an SSB/CW receiver, what is the purpose of the radio frequency (RF) amplifier?

A.
Increase the sensitivity of the receiver (100% chose this)
B.
Provide sufficient gain to activate the limiter circuit (0% chose this)
C.
Provide sufficient drive for the automatic gain control circuit (AGC) (0% chose this)
D.
Increase the local oscillator signal to drive the mixer (0% chose this)

B-003-012-010

Your SSB transmitter is set to operate lower sideband at 7100 kHz. With a single 1000 Hz tone as modulation, at which frequency is RF transmitted?

A.
7101 kHz (50% chose this)
B.
6100 kHz (0% chose this)
C.
7099 kHz (50% chose this)
D.
8100 kHz (0% chose this)

B-001-016-001

What is the maximum authorized bandwidth on the 6-metre and 2-metre bands?

A.
30 kHz (100% chose this)
B.
6 kHz (0% chose this)
C.
20 kHz (0% chose this)
D.
5 kHz (0% chose this)

B-001-015-011

In Canada, which bands may amateur radio operators use for radio control of models?

A.
All amateur radio bands above 30 MHz (100% chose this)
B.
50 MHz to 54 MHz, 144 MHz to 148 MHz, and 222 MHz to 225 MHz only (0% chose this)
C.
All amateur radio bands (0% chose this)
D.
50 MHz to 54 MHz only (0% chose this)

B-001-023-008

The proponent of an antenna system and a stakeholder, other than the general public, have failed to reach an agreement. How is a final decision reached?

A.
The decision is made by Innovation, Science and Economic Development Canada (100% chose this)
B.
The decision is made by the local municipality (0% chose this)
C.
The decision is postponed until an agreement is reached (0% chose this)
D.
The decision is made by a majority vote of residents within a radius of three times the antenna height (0% chose this)

B-003-007-006

Why are some transceivers capable of operating computer-based digital modes without a separate sound card?

A.
Because they support CAT (Computer Aided Transceiver) (50% chose this)
B.
Because they incorporate an audio codec (50% chose this)
C.
Because they provide a USB connector (0% chose this)
D.
Because digital signal processing (DSP) is built-in (0% chose this)

B-003-016-002

Which of the following has a positive terminal and a negative terminal?

A.
A resistor (0% chose this)
B.
A potentiometer (0% chose this)
C.
A fuse (0% chose this)
D.
A battery (100% chose this)

B-005-012-006

In a parallel-resonant circuit at resonance, the circuit has:

A.
low impedance (0% chose this)
B.
high impedance (100% chose this)
C.
high mutual inductance (0% chose this)
D.
low mutual inductance (0% chose this)

B-006-005-005

What is the main adverse effect due to operating with high SWR?

A.
Increased receive noise level (0% chose this)
B.
Increased transmission line radiation (0% chose this)
C.
Increased transmission line loss (50% chose this)
D.
Increased common-mode current (50% chose this)

B-006-010-011

When using a ground mounted vertical HF antenna, what can you do to reduce ground losses?

A.
Raise the antenna one eighth of a wavelength (0% chose this)
B.
Use an insulator with a higher breakdown voltage (0% chose this)
C.
Improve the impedance match at the base (0% chose this)
D.
Install a wire ground system (radials) at the antenna base (100% chose this)

B-002-009-006

Local stations are in contact with New Zealand, yet you cannot hear the New Zealand amateur radio operators with your antenna pointed in that direction. What other antenna direction could you try to hear them?

A.
Point your antenna 90 degrees west of the current bearing (0% chose this)
B.
Point your antenna further south (0% chose this)
C.
Point your antenna 90 degrees east of the current bearing (0% chose this)
D.
Point your antenna 180 degrees from the current bearing (100% chose this)

B-001-016-005

The maximum bandwidth of an amateur radio station's transmission allowed in the band 50 MHz to 54 MHz is:

A.
6 kHz (0% chose this)
B.
15 kHz (0% chose this)
C.
30 kHz (100% chose this)
D.
20 kHz (0% chose this)

B-002-008-005

What is the correct way to interrupt a repeater conversation to seek assistance in a distress situation?

A.
Say "HELP" as many times as it takes to get someone to answer (0% chose this)
B.
Break-in between transmissions to state your call sign and situation (100% chose this)
C.
Say "SOS," then your call sign (0% chose this)
D.
Say "EMERGENCY" three times (0% chose this)

B-003-004-002

In a basic CW transmitter, what type of electricity directly powers each stage?

A.
Direct current (100% chose this)
B.
Radio frequency current (0% chose this)
C.
Audio frequency current (0% chose this)
D.
Alternating current (0% chose this)

B-001-023-006

Innovation, Science and Economic Development Canada's default public consultation process for antenna systems requires proponents to address:

A.
reasonable and relevant concerns provided in writing within the 30-day public comment period (100% chose this)
B.
all questions, comments and concerns raised (0% chose this)
C.
comments reported in the media (0% chose this)
D.
opposition to the project (0% chose this)

B-002-004-004

How can on-the-air interference be minimized during lengthy transmitter testing?

A.
Use a non-resonant antenna (0% chose this)
B.
Use a resonant antenna (0% chose this)
C.
Use a dummy load (100% chose this)
D.
Choose an unoccupied frequency (0% chose this)

B-002-007-006

What is the correct Q code to ask who is calling you?

A.
QRZ? (100% chose this)
B.
QRT? (0% chose this)
C.
QSL? (0% chose this)
D.
QRL? (0% chose this)

B-003-003-010

In an FM receiver, which stage includes a squelch circuit?

A.
AF amplifier (100% chose this)
B.
Product detector (0% chose this)
C.
Limiter (0% chose this)
D.
IF amplifier (0% chose this)

B-006-013-009

What is the approximate length of the wire for a horizontal loop tuned at 7.15 MHz?

A.
41.96 metres (0% chose this)
B.
42.80 metres (100% chose this)
C.
20.00 metres (0% chose this)
D.
10.49 metres (0% chose this)

B-003-006-002

In a single-sideband transmitter, why is the speech amplifier needed?

A.
Microphones usually have a low power output (50% chose this)
B.
To match the balanced modulator's output impedance (0% chose this)
C.
The sideband filter requires a large audio signal to work (50% chose this)
D.
To improve signal fidelity (0% chose this)

B-002-004-005

Why would you use a dummy load?

A.
To test or adjust your transceiver without causing interference (100% chose this)
B.
It is faster to tune (0% chose this)
C.
To give comparative signal reports (0% chose this)
D.
To reduce output power (0% chose this)

B-001-015-004

The holder of an Amateur Radio Operator Certificate may operate radio-controlled models:

A.
on all amateur radio bands above 30 MHz (100% chose this)
B.
if only pulse modulation is used (0% chose this)
C.
if the control transmitter does not exceed 15 kHz of occupied bandwidth (0% chose this)
D.
on all amateur radio bands below 30 MHz (0% chose this)

B-005-010-006

What circuit parameter change causes an inductor's reactance to increase?

A.
A decrease in frequency (0% chose this)
B.
An increase in current (0% chose this)
C.
An increase in voltage (0% chose this)
D.
An increase in frequency (100% chose this)

B-003-018-001

How could you best keep unauthorized persons from using your station at home?

A.
Put a "Danger - High Voltage" sign in the station (0% chose this)
B.
Use a key-operated on/off switch in the main power line (100% chose this)
C.
Put fuses in the main power line (0% chose this)
D.
Use a carrier-operated relay in the main power line (0% chose this)

B-001-020-001

What types of messages may be transmitted to an amateur radio station in a foreign country?

A.
Messages of any type, if the foreign country allows third-party communications with Canada (0% chose this)
B.
Messages that are not religious, political, or patriotic in nature (0% chose this)
C.
Messages of any type (0% chose this)
D.
Messages related to the purposes of amateur radio or remarks of a personal nature (100% chose this)

B-001-013-002

How often must an amateur radio station be identified?

A.
At the beginning and end of each transmission (0% chose this)
B.
At least once during each transmission (0% chose this)
C.
At the beginning of a contact and at least every thirty minutes after that (0% chose this)
D.
At least every thirty minutes, and at the beginning and at the end of a contact (100% chose this)

B-003-005-010

In an SSB/CW receiver, which stage could include an audio band-pass filter?

A.
AF amplifier (100% chose this)
B.
IF amplifier (0% chose this)
C.
IF filter (0% chose this)
D.
Limiter (0% chose this)

B-006-004-005

As the frequency of a signal is changed, what happens to signal loss in a transmission line?

A.
Signal loss increases with decreasing frequency (0% chose this)
B.
Signal loss increases as the square of frequency (0% chose this)
C.
Signal loss is the same for any frequency (0% chose this)
D.
Signal loss increases with increasing frequency (100% chose this)

B-002-003-002

How should you answer a voice CQ call?

A.
Say your call sign twice, followed by "calling," then the other station's call sign (0% chose this)
B.
Say the other station's call sign at least five times, followed by "this is," then your call sign twice (0% chose this)
C.
Say the other station's call sign at least three times, followed by "this is," and your call sign at least five times (0% chose this)
D.
Say the other station's call sign once, followed by "this is," then your call sign (100% chose this)

B-001-014-007

International third-party amateur radio communication in case of emergencies or disaster relief is expressly permitted unless:

A.
satellite communication can be originated in the disaster area (0% chose this)
B.
specifically prohibited by the foreign administration concerned (100% chose this)
C.
internet service is working well in the foreign country involved (0% chose this)
D.
the foreign administration is in a declared state of war (0% chose this)

B-001-014-001

If a friend without amateur radio certification is using your station to talk to someone in Canada, and a foreign station breaks in to talk to your friend, what should you do?

A.
Take over the conversation with the Canadian and foreign station (0% chose this)
B.
Instruct your friend to ignore the foreign station (0% chose this)
C.
Stop all discussions and quickly sign off (0% chose this)
D.
Continue monitoring the communications of your friend (100% chose this)

B-002-005-007

What is meant by the term "DX"?

A.
Calling any station (0% chose this)
B.
Distant station (100% chose this)
C.
Best regards (0% chose this)
D.
Go ahead (0% chose this)

B-001-024-004

Why is the limit of exposure to RF the lowest in the frequency range of 48 MHz to 300 MHz, according to Safety Code 6?

A.
Most transmissions in this range are for a longer time (0% chose this)
B.
There are more transmitters operating in this range (0% chose this)
C.
There are fewer transmitters operating in this range (0% chose this)
D.
The human body absorbs RF energy the most in this range (100% chose this)

B-002-008-008

Which type of antenna would be a good choice as part of a portable HF station that could be set up in case of an emergency?

A.
A dipole or a vertical (100% chose this)
B.
A three-element quad (0% chose this)
C.
A three-element Yagi (0% chose this)
D.
A parabolic dish (0% chose this)

B-001-002-003

Whenever a change of address is made:

A.
you must not operate until a change of address card is forwarded to Innovation, Science and Economic Development Canada (0% chose this)
B.
you must notify Innovation, Science and Economic Development Canada within 30 days of a change of mailing address (100% chose this)
C.
you must notify Innovation, Science and Economic Development Canada within 14 days of operation at the new address (0% chose this)
D.
within the same province, you do not need to notify Innovation, Science and Economic Development Canada (0% chose this)

B-002-001-004

What is the purpose of a repeater time-out timer?

A.
It hands over control to each user in turns (0% chose this)
B.
It logs repeater transmit time to predict when a repeater will fail (0% chose this)
C.
It tells how long someone has been using a repeater (0% chose this)
D.
It interrupts lengthy transmissions (100% chose this)

B-007-006-006

What usually happens to radio waves with frequencies below the maximum usable frequency (MUF) when they are sent into the ionosphere?

A.
They are changed to a frequency above the MUF (0% chose this)
B.
They are completely absorbed by the ionosphere (0% chose this)
C.
They pass through the ionosphere (0% chose this)
D.
They are bent back to the Earth (100% chose this)

B-001-023-002

Who has authority over antenna installations, including antenna masts and towers?

A.
The provincial or territorial Minister of Infrastructure (0% chose this)
B.
The Minister of Innovation, Science and Industry (100% chose this)
C.
The majority of neighbours within a distance of three times the proposed antenna height (0% chose this)
D.
The local municipal government (0% chose this)

B-002-004-006

If you are the net control station of a daily HF net, what should you do if the frequency on which you normally meet is in use just before the net begins?

A.
Reduce your output power and start the net as usual (0% chose this)
B.
Cancel the net for that day (0% chose this)
C.
Increase your power output so that net participants will be able to hear you over the existing activity (0% chose this)
D.
Ask occupants if they would change frequency, otherwise move to a clear frequency (100% chose this)

B-003-006-008

In a single-sideband transmitter, which stage normally includes a circuit providing protection from excessive SWR?

A.
Speech amplifier (0% chose this)
B.
Final amplifier (100% chose this)
C.
Variable frequency oscillator (0% chose this)
D.
Balanced modulator (0% chose this)

B-001-004-006

You hold an Amateur Radio Operator Certificate with Advanced Qualification. Besides the amateur radio service, in what other service does this authorization allow you to operate a station?

A.
Aeronautical service (0% chose this)
B.
No other service (100% chose this)
C.
Land mobile service (0% chose this)
D.
Maritime service (0% chose this)

B-002-001-009

What is the proper way to join a conversation on a repeater?

A.
Say your call sign during a break between transmissions (100% chose this)
B.
Wait for the end of a transmission and start calling the desired party (0% chose this)
C.
Shout "break, break!" to show that you're eager to join the conversation (0% chose this)
D.
Increase power to override whoever is talking (0% chose this)

B-002-009-005

What method is used by amateur radio operators to provide proof of communication with another station?

A.
A QSL card or entries in web-based logging systems (100% chose this)
B.
A brief email or text message (0% chose this)
C.
A radiogram sent over amateur radio traffic nets (0% chose this)
D.
A letter detailing contact date, time, frequency, mode and power (0% chose this)

B-006-002-004

What is the purpose of a balun?

A.
Connect balanced and unbalanced systems (100% chose this)
B.
Balance antenna impedance (0% chose this)
C.
Shunt common-mode current to ground (0% chose this)
D.
Increase antenna gain (0% chose this)

B-001-001-002

Which document assigns the authority to publish Standards for the Operation of Radio Stations in the Amateur Radio Service in Canada?

A.
The Broadcasting Act (0% chose this)
B.
The Radiocommunication Act (100% chose this)
C.
The Radiocommunication Regulations (0% chose this)
D.
The International Telecommunication Union's Radio Regulations (0% chose this)

B-002-005-003

At what speed should a Morse code "CQ" call be transmitted?

A.
At the customary speed for the band (0% chose this)
B.
At the highest speed your keyer will operate (0% chose this)
C.
At the highest speed at which you can control the keyer (0% chose this)
D.
At any speed which you can reliably receive (100% chose this)

B-002-006-001

What do "RST" signal reports describe?

A.
Ionospheric conditions (0% chose this)
B.
Transmitter power (0% chose this)
C.
Signal reception (100% chose this)
D.
Sunspot activity (0% chose this)

B-001-013-010

What are the station identification requirements for a test transmission?

A.
Identification is only needed on voice modes (0% chose this)
B.
Brief test transmissions need not be identified (0% chose this)
C.
Identification shall be transmitted at five-minute intervals (0% chose this)
D.
The rules are the same for a test or a radio contact (100% chose this)

B-001-021-002

A Canadian amateur radio operator, operating their station in the state of Florida, is subject to which frequency band limits?

A.
Those applicable in International Telecommunication Union region 3 (0% chose this)
B.
Those applicable in International Telecommunication Union region 1 (0% chose this)
C.
Those applicable in International Telecommunication Union region 2 (0% chose this)
D.
Those applicable to United States amateur radio operators (100% chose this)

B-001-023-003

When may you NOT be required to contact land-use authorities to determine public consultation requirements for an antenna system?

A.
When the structure is part of an amateur radio antenna (0% chose this)
B.
When transmitting will only be done at low power (0% chose this)
C.
When an exclusion criterion defined by Innovation, Science and Economic Development Canada applies (100% chose this)
D.
In a rural area (0% chose this)

B-003-009-002

In a 3-element Yagi antenna, what is the longest radiating element?

A.
The boom (0% chose this)
B.
The director (0% chose this)
C.
The driven element (50% chose this)
D.
The reflector (50% chose this)

B-001-009-006

When an amateur radio station is transmitting, where must its control operator be?

A.
At the station's entrance, to control entry to the room (0% chose this)
B.
At the station's control point (100% chose this)
C.
Anywhere within 50 km of the station location (0% chose this)
D.
Anywhere in the same building as the transmitter (0% chose this)

B-002-005-006

What is the meaning of the Morse code signal "K"?

A.
Any station please reply (100% chose this)
B.
Called station only reply (0% chose this)
C.
All received correctly (0% chose this)
D.
End of message (0% chose this)

B-001-021-004

In which region of the International Telecommunication Union are Australia, Japan, and Southeast Asia located?

A.
Region 1 (0% chose this)
B.
Region 3 (100% chose this)
C.
Region 4 (0% chose this)
D.
Region 2 (0% chose this)

B-003-012-011

The automatic level control (ALC) in an SSB transmitter:

A.
reduces transmitter audio feedback (0% chose this)
B.
reduces system noise (0% chose this)
C.
limits the input audio peaks so that the transmitter is not overdriven (100% chose this)
D.
increases the occupied bandwidth (0% chose this)

B-002-003-010

Which sideband is commonly used on 3755 kHz for voice operation?

A.
Upper (0% chose this)
B.
Lower (100% chose this)
C.
Double (0% chose this)
D.
Independent (0% chose this)

B-006-006-004

If both source and load impedances are purely resistive, what value of load impedance will result in maximum power delivery to the load?

A.
Load impedance equal to twice the source impedance (0% chose this)
B.
Load impedance equal to the source impedance (100% chose this)
C.
Load impedance equal to half of the source impedance (0% chose this)
D.
Load impedance equal to the square root of source impedance (0% chose this)

B-002-007-007

What does the code "QRM" mean in amateur radio?

A.
I am busy (0% chose this)
B.
I am being interfered with (100% chose this)
C.
I am troubled by static (0% chose this)
D.
Your signals are fading (0% chose this)

B-003-009-001

Which component of a 3-element Yagi antenna is primarily for mechanical support?

A.
The boom (100% chose this)
B.
The driven element (0% chose this)
C.
The director (0% chose this)
D.
The reflector (0% chose this)

B-002-004-011

Before transmitting, the first thing you should do is:

A.
ask if the frequency is occupied (0% chose this)
B.
make an announcement on the frequency indicating that you intend to make a call (0% chose this)
C.
decrease your receiver's volume (0% chose this)
D.
listen carefully so as not to interrupt communications already in progress (100% chose this)

B-003-004-006

In a basic CW transmitter, what does the key do?

A.
It switches the carrier on and off (100% chose this)
B.
It switches the carrier between two frequencies (0% chose this)
C.
It switches the transmitted tone on and off (0% chose this)
D.
It makes and breaks the antenna connection (0% chose this)

B-001-019-003

Amateur radio stations are required to have means of indicating or preventing a signal quality problem unique to voice transmissions. What is it?

A.
Inadequate pre-emphasis (0% chose this)
B.
Excessive compression (0% chose this)
C.
Overmodulation (100% chose this)
D.
Inadequate audio filtering (0% chose this)

B-003-001-009

When using an HF transmitter with a solid-state final amplifier, which station component may need to be adjusted when changing frequency?

A.
SWR meter (0% chose this)
B.
Low-pass filter (0% chose this)
C.
Dummy load (0% chose this)
D.
Antenna tuner (100% chose this)

B-003-006-006

In a single-sideband transmitter, which stage transposes the single-sideband signal to the operating frequency?

A.
Fixed RF oscillator (0% chose this)
B.
Variable frequency oscillator (0% chose this)
C.
Balanced modulator (0% chose this)
D.
Mixer (100% chose this)

B-004-003-003

What are the three electrodes of a bipolar transistor?

A.
Collector, source and drain (0% chose this)
B.
Gate, source and drain (0% chose this)
C.
Drain, base and source (0% chose this)
D.
Collector, emitter and base (100% chose this)

B-003-001-007

In an HF station, which component is designed to dissipate RF energy and prevent radiation?

A.
Dummy load (50% chose this)
B.
Lightning surge protector (50% chose this)
C.
Low-pass filter (0% chose this)
D.
Heat sink (0% chose this)

B-001-008-007

What minimum qualifications must an amateur radio operator hold to operate cross-band repeaters?

A.
Basic with Honours (0% chose this)
B.
Basic and Morse code (0% chose this)
C.
Basic (100% chose this)
D.
Basic and Advanced (0% chose this)

B-005-003-008

Which two electrical units multiplied together give the unit "watts"?

A.
Volts and farads (0% chose this)
B.
Amperes and henries (0% chose this)
C.
Farads and henries (0% chose this)
D.
Volts and amperes (100% chose this)

B-001-013-007

When may an amateur radio operator transmit unidentified communications?

A.
Only to control a model craft (100% chose this)
B.
Only for two-way or third-party communications (0% chose this)
C.
Only if it does not interfere with others (0% chose this)
D.
Only for brief tests not meant as messages (0% chose this)

B-002-005-010

When selecting a CW transmitting frequency, what minimum frequency separation from a contact in progress should you allow to minimize interference?

A.
3 kHz to 6 kHz (0% chose this)
B.
5 Hz to 50 Hz (0% chose this)
C.
150 Hz to 500 Hz (100% chose this)
D.
1 kHz to 3 kHz (0% chose this)

B-002-005-005

What is the meaning of the word "DE" in Morse code?

A.
Directional Emissions (0% chose this)
B.
From (100% chose this)
C.
Calling any station (0% chose this)
D.
Received all correctly (0% chose this)

B-001-010-002

When may you deliberately interfere with another amateur radio station's communications?

A.
Deliberate interference is never acceptable (100% chose this)
B.
Only if the station is operating illegally (0% chose this)
C.
Only if the station begins transmitting on a frequency you are using (0% chose this)
D.
Only when you are operating within crowded band conditions (0% chose this)

B-004-002-008

What semiconductor device glows different colours, depending upon its chemical composition?

A.
A neon bulb (0% chose this)
B.
A light-emitting diode (100% chose this)
C.
A vacuum diode (0% chose this)
D.
A fluorescent bulb (0% chose this)

B-001-006-003

Under what circumstances is an amateur radio operator permitted to use an amplifier to amplify the output of a licence-exempt transmitter?

A.
This is not permitted (100% chose this)
B.
When emissions will be outside amateur radio frequency allocations (0% chose this)
C.
Only for short test transmissions (0% chose this)
D.
When other users will not be interfered with (0% chose this)

B-001-014-005

Foreign amateur radio operators may operate in Canada if they qualify for a CEPT (European Conference of Postal and Telecommunications Administrations) Amateur Radio Licence. What operating privileges are they granted by Innovation, Science and Economic Development Canada?

A.
Advanced (100% chose this)
B.
Basic and Morse code (0% chose this)
C.
Basic with Honours (0% chose this)
D.
Basic (0% chose this)

B-001-010-003

If the regulations say that the amateur radio service is a secondary user of a frequency band, and another service is a primary user, what does this mean?

A.
Amateur radio operators can only use the band briefly for radio testing and adjustment purposes (0% chose this)
B.
Amateur radio operators are only allowed to use the frequency band during emergencies (0% chose this)
C.
Nothing special: all users of a frequency band have equal rights to operate (0% chose this)
D.
Amateur radio operators are allowed to use the frequency band only if they do not cause interference to primary users (100% chose this)

B-001-019-004

What is the maximum percentage of modulation permitted for amateur radio voice communications?

A.
50% (0% chose this)
B.
90% (0% chose this)
C.
100% (100% chose this)
D.
75% (0% chose this)

B-002-002-001

To make your call sign better understood when using voice transmissions, what should you do?

A.
Use any words which start with the same letters as your call sign for each letter of your call (0% chose this)
B.
Use International Telecommunication Union phonetic alphabet code words to spell letters in your call sign (100% chose this)
C.
Talk louder and faster (0% chose this)
D.
Turn up your microphone gain (0% chose this)

B-001-009-001

Who is responsible for the operation of an amateur radio station?

A.
Only the station owner who is the holder of an Amateur Radio Operator Certificate (0% chose this)
B.
Only the control operator (0% chose this)
C.
The person who owns the station equipment (0% chose this)
D.
Both the control operator and the station owner (100% chose this)

B-001-001-001

Which document assigns the authority to make Canadian regulations governing radiocommunications?

A.
The Broadcasting Act (0% chose this)
B.
The Radiocommunication Act (100% chose this)
C.
The International Telecommunication Union's Radio Regulations (0% chose this)
D.
The Standards for the Operation of Radio Stations in the Amateur Radio Service (0% chose this)

B-001-014-011

Canadian amateur radio stations may provide communications on behalf of third parties:

A.
only in cases of emergencies or disaster relief (0% chose this)
B.
on frequencies assigned to the Canadian Forces Affiliate Radio Service (CFARS) (0% chose this)
C.
only with countries that have third-party traffic agreements with Canada (0% chose this)
D.
with any other amateur radio station (100% chose this)

B-002-004-001

What should you do before you transmit on any frequency?

A.
Make sure the SWR on your transmission line is high enough (0% chose this)
B.
Check your antenna for resonance at the selected frequency (0% chose this)
C.
Increase power to ensure someone will hear you (0% chose this)
D.
Listen to make sure others are not using the frequency (100% chose this)

B-007-001-004

On VHF and higher frequencies, why does the radio horizon extend beyond the visible horizon?

A.
Diffraction caused by soil conductivity (0% chose this)
B.
Normal refraction in the troposphere (100% chose this)
C.
Ionization in the troposphere (0% chose this)
D.
Refraction in the D-region (0% chose this)

B-003-010-003

What are the two signal parameters presented to the user on the waterfall display (spectrogram) of a modern receiver?

A.
Frequency and phase (0% chose this)
B.
Amplitude and frequency (100% chose this)
C.
Bandwidth and digital mode (0% chose this)
D.
Phase and bandwidth (0% chose this)

B-002-009-007

Which statement about recording all contacts and unanswered CQ calls in a paper or computer-based station logbook is NOT correct?

A.
A logbook is important for recording contacts for operating awards (0% chose this)
B.
A logbook is a regulatory requirement (100% chose this)
C.
A logbook is important for handling neighbour interference complaints (0% chose this)
D.
A well-kept logbook preserves your fondest amateur radio memories for years (0% chose this)

B-002-006-002

What does "RST" stand for in a signal report?

A.
Recovery, signal speed, tone (0% chose this)
B.
Readability, signal speed, tempo (0% chose this)
C.
Readability, signal strength, tone (100% chose this)
D.
Recovery, signal strength, tempo (0% chose this)

B-002-002-008

In the International Telecommunication Union phonetic alphabet, what is the code word for the letter I?

A.
Iran (0% chose this)
B.
Italy (0% chose this)
C.
India (100% chose this)
D.
Item (0% chose this)

B-001-016-007

In which of the following amateur radio bands is single sideband prohibited?

A.
7.000 MHz to 7.300 MHz (50% chose this)
B.
10.100 MHz to 10.150 MHz (50% chose this)
C.
18.068 MHz to 18.168 MHz (0% chose this)
D.
24.890 MHz to 24.990 MHz (0% chose this)

B-003-011-006

Morse code is usually transmitted by radio as:

A.
a continuous carrier (0% chose this)
B.
an interrupted carrier (100% chose this)
C.
a series of key clicks (0% chose this)
D.
a phase-shifted carrier (0% chose this)

B-003-013-009

Why isn't FM used as an amateur radio emission mode below 28 MHz?

A.
Harmonics could not be attenuated to practical levels (0% chose this)
B.
The frequency stability would not be adequate (0% chose this)
C.
The transmitter efficiency for this mode is low (0% chose this)
D.
The bandwidth would exceed limits in the regulations (100% chose this)

B-002-007-003

What is the proper Q code to use to see if a frequency is in use before transmitting on CW?

A.
QRU? (0% chose this)
B.
QRV? (0% chose this)
C.
QRL? (100% chose this)
D.
QRZ? (0% chose this)

B-001-022-004

What is the fee for taking Amateur Radio Operator Certificate examinations at an Innovation, Science and Economic Development Canada office?

A.
$20 per visit, regardless of the number of qualification examinations (0% chose this)
B.
$20 per qualification (0% chose this)
C.
No charge for qualification examinations (100% chose this)
D.
$5 per qualification examination (0% chose this)

B-002-007-008

What does the code "QRN" mean in amateur radio?

A.
I am busy (0% chose this)
B.
I am being interfered with (0% chose this)
C.
I am troubled by static (100% chose this)
D.
I will call you (0% chose this)

B-001-015-007

What is the frequency range of the 40-metre amateur radio band in Canada?

A.
6.5 MHz to 6.8 MHz (0% chose this)
B.
6.0 MHz to 6.3 MHz (0% chose this)
C.
7.7 MHz to 8.0 MHz (0% chose this)
D.
7.0 MHz to 7.3 MHz (100% chose this)

B-002-002-003

In the International Telecommunication Union phonetic alphabet, what is the code word for the letter A?

A.
Alfa (100% chose this)
B.
Adam (0% chose this)
C.
Able (0% chose this)
D.
America (0% chose this)

B-002-005-009

Which of the following describes full break-in CW (QSK)?

A.
An operator must activate a manual send/receive switch before and after every transmission (0% chose this)
B.
Incoming signals are received between transmitted dots and dashes (100% chose this)
C.
Stations wishing to break in must send the Morse code signal "BK" (0% chose this)
D.
Automatic keyers are used instead of hand keys (0% chose this)

B-001-016-008

What precaution must an amateur radio operator take when transmitting near band edges?

A.
Reduce transmitter power (0% chose this)
B.
Restrict operation to radiotelegraphy (CW) or digital modes (0% chose this)
C.
Ensure that the entire occupied bandwidth falls within the amateur radio band (100% chose this)
D.
Make sure that the emission mode is compatible with agreed band plans (0% chose this)

B-002-003-004

When should you consider using simplex operation instead of a repeater?

A.
When an emergency telephone call is needed (0% chose this)
B.
When you are travelling and need some local information (0% chose this)
C.
When signals are reliable between communicating parties without using a repeater (100% chose this)
D.
When the most reliable communications are needed (0% chose this)

B-003-008-004

What is the purpose of the filter in a linear power supply?

A.
Absorb the power produced by the supply (0% chose this)
B.
Convert alternating current into direct current (0% chose this)
C.
Ensure that the voltage stays constant when a heavy demand is placed on the supply (0% chose this)
D.
Smooth out pulsating direct current (100% chose this)

B-003-011-002

What can be done to keep a CW transmitter from chirping?

A.
Keep the power supply voltages very steady under varying loads (100% chose this)
B.
Add a key click filter (0% chose this)
C.
Add a low-pass filter (0% chose this)
D.
Keep the oscillator impedance very steady under the transmit load (0% chose this)

B-003-011-010

The DC power to the final stage of your transmitter is 200 watts and the RF output is 125 watts. What has happened to the rest of the power?

A.
It has been used to provide negative feedback (0% chose this)
B.
It has been dissipated as heat (100% chose this)
C.
It has been used to provide positive feedback (0% chose this)
D.
It has been used to provide greater efficiency (0% chose this)

B-001-011-004

In the amateur radio service, it is permissible to broadcast:

A.
programming that originates from a broadcast undertaking (0% chose this)
B.
commercially recorded material (0% chose this)
C.
music that is picked up by your microphone (0% chose this)
D.
radio communications required for the safety of life and property (100% chose this)

B-001-014-004

What condition would preclude a Canadian amateur radio station from communicating with amateur radio stations in another country?

A.
The country is not a member of the International Amateur Radio Union (IARU) (0% chose this)
B.
The conversation is not conducted totally in English or French (0% chose this)
C.
The country has filed an objection to such communications with the International Telecommunication Union (ITU) (100% chose this)
D.
It is prohibited by Innovation, Science and Economic Development Canada (0% chose this)

B-001-010-006

In the event the Minister of Innovation, Science and Industry determines that an amateur radio station causes harmful interference, what are the Minister's powers?

A.
Revoke the amateur radio operator's certificate without giving written notice (0% chose this)
B.
Order the station's operation to cease or change (100% chose this)
C.
Delegate the matter to the Canadian Radio-television and Telecommunications Commission (0% chose this)
D.
Convene the parties to arrive at a compromise solution (0% chose this)

B-003-006-001

In a single-sideband transmitter, what does the fixed RF oscillator do?

A.
It produces an RF carrier (100% chose this)
B.
It drives the mixer (0% chose this)
C.
It directly drives the sideband filter (0% chose this)
D.
It balances the variable frequency oscillator (0% chose this)

B-002-005-008

What is the meaning of the term "73"?

A.
Love and kisses (0% chose this)
B.
Long distance (0% chose this)
C.
Best regards (100% chose this)
D.
Go ahead (0% chose this)

B-008-005-007

A strong interfering signal is very close to your receive frequency. Which type of filter can effectively suppress it?

A.
Low-pass (0% chose this)
B.
High-pass (0% chose this)
C.
Notch (100% chose this)
D.
Band-reject (0% chose this)

B-003-010-009

A communications receiver has four filters installed in it, respectively designated as 250 Hz, 500 Hz, 2.4 kHz, and 6 kHz. If you were listening to single sideband, which filter would you utilize?

A.
6 kHz (0% chose this)
B.
250 Hz (0% chose this)
C.
500 Hz (0% chose this)
D.
2.4 kHz (100% chose this)

B-002-008-003

What voice signal, transmitted three times, signifies distress?

A.
EMERGENCY (0% chose this)
B.
SOS (0% chose this)
C.
MAYDAY (100% chose this)
D.
HELP (0% chose this)

B-002-003-001

What is the correct way to call "CQ" when using voice?

A.
Say "CQ" once, followed by "this is," followed by your call sign spoken three times (0% chose this)
B.
Say "CQ" at least five times, followed by "this is," followed by your call sign spoken once (0% chose this)
C.
Say "CQ" at least ten times, followed by "this is," followed by your call sign spoken once (0% chose this)
D.
Say "CQ" three times, followed by "this is," followed by your call sign spoken three times (100% chose this)

B-002-003-007

If you are talking to a station using a repeater, how would you find out if you could communicate using simplex instead?

A.
By asking the other station to move 10 kHz away to test the path (0% chose this)
B.
By asking a third station to confirm it receives you both (0% chose this)
C.
By checking if you can clearly receive the station on the repeater's input frequency (100% chose this)
D.
By checking if you can clearly receive a more distant repeater (0% chose this)

B-001-009-008

The owner of an amateur radio station may:

A.
permit any person to operate the station under the supervision and in the presence of the holder of an Amateur Radio Operator Certificate (100% chose this)
B.
permit anyone to take part in communications only if prior written permission is received from Innovation, Science and Economic Development Canada (0% chose this)
C.
permit anyone to use the station without restrictions (0% chose this)
D.
permit anyone to use the station and take part in communications (0% chose this)

B-001-015-002

If you are the control operator at the station of another amateur radio operator who has more certificate qualifications than you, what operating privileges are you allowed?

A.
Only the privileges allowed by your qualifications (100% chose this)
B.
All the frequency privileges of the additional qualifications, but only the emission privileges of your qualifications (0% chose this)
C.
All the emission privileges of the additional qualifications, but only the frequency privileges of your qualifications (0% chose this)
D.
Any privileges allowed by the additional qualifications (0% chose this)

B-002-006-007

Your receiver's S-meter is calibrated to a standard of 6 dB per S-unit per a recommendation by the International Amateur Radio Union (IARU). The S-meter shows S9 when receiving a station transmitting with 100 watts. Neglecting propagation changes, what transmitter power would cause your receiver's S-meter to read S8?

A.
33 watts (0% chose this)
B.
50 watts (0% chose this)
C.
25 watts (100% chose this)
D.
75 watts (0% chose this)

B-002-009-011

What is the usefulness of stations CHU, WWV and WWVH to amateur radio operators?

A.
Provide amateur radio bulletins (0% chose this)
B.
Provide accurate and precise frequency and time signals (100% chose this)
C.
Provide forecasts of band conditions (0% chose this)
D.
Provide received signal reports of your transmissions (0% chose this)

B-001-019-005

What must all amateur radio stations be capable of reliably measuring, regardless of emission mode?

A.
Frequency (100% chose this)
B.
Modulation (0% chose this)
C.
SWR (0% chose this)
D.
RF power (0% chose this)

B-002-008-006

What is the advantage of preparing to operate your station without commercial AC power?

A.
So you will comply with the rules (0% chose this)
B.
So you may operate in contests where AC power is not allowed (0% chose this)
C.
So you may use your station while mobile (0% chose this)
D.
So you may provide communications during a power outage (100% chose this)

B-006-007-010

If an electromagnetic wave leaves an antenna vertically polarized and reaches the receiving location by ground wave, what will be its final polarization?

A.
Oblique (0% chose this)
B.
Circular (0% chose this)
C.
Horizontal (0% chose this)
D.
Vertical (100% chose this)

B-002-002-004

In the International Telecommunication Union phonetic alphabet, what is the code word for the letter B?

A.
Bravo (100% chose this)
B.
Baker (0% chose this)
C.
Borneo (0% chose this)
D.
Brazil (0% chose this)

B-002-004-002

If you contact another station and your signal is extremely strong and perfectly readable, what adjustment should you make to your transmitter?

A.
None, continue with your contact (0% chose this)
B.
Turn down your power output to the minimum necessary (100% chose this)
C.
Bypass your antenna tuner (0% chose this)
D.
Turn on your speech processor (0% chose this)

B-001-002-002

An Amateur Radio Operator Certificate is valid for:

A.
five years (0% chose this)
B.
life (100% chose this)
C.
three years (0% chose this)
D.
one year (0% chose this)

B-003-002-007

In an FM transmitter, which stage draws the most electric power?

A.
Speech amplifier (0% chose this)
B.
Power amplifier (100% chose this)
C.
Oscillator (0% chose this)
D.
Frequency multiplier (0% chose this)

B-003-003-006

In a superheterodyne receiver, which stage provides the final signal power to drive the detector?

A.
Frequency multiplier (0% chose this)
B.
IF amplifier (100% chose this)
C.
RF amplifier (0% chose this)
D.
Speech amplifier (0% chose this)

B-003-004-001

In a basic CW transmitter, the output from the oscillator is:

A.
at the transmitted signal's power level (0% chose this)
B.
at a submultiple of the operating frequency (0% chose this)
C.
less stable than the transmitted signal (0% chose this)
D.
at the transmitted signal's frequency (100% chose this)

B-001-017-008

On 630 metres and 2200 metres, what key antenna characteristic must be taken into account to comply with power limitations expressed as equivalent isotropically radiated power (EIRP)?

A.
Gain (100% chose this)
B.
Resonance (0% chose this)
C.
Bandwidth (0% chose this)
D.
Impedance (0% chose this)

B-001-005-002

Under what circumstances can an amateur radio operator reprogram a land mobile transmitter on behalf of another person for use on 2 metres?

A.
Only if an amateur radio operator with an Advanced Qualification performs the modification (0% chose this)
B.
Only if the other person holds an Amateur Radio Operator Certificate (100% chose this)
C.
Only if the other person holds an Advanced Qualification (0% chose this)
D.
Only if the other person holds a Basic with Honours Qualification (0% chose this)

B-007-005-009

Average duration of a solar cycle is:

A.
6 years (0% chose this)
B.
1 year (0% chose this)
C.
3 years (0% chose this)
D.
11 years (100% chose this)

B-001-008-008

What minimum qualifications must an amateur radio operator hold to remotely operate a transmitter, including changing frequency, emission mode or output power?

A.
Basic and Advanced (100% chose this)
B.
Basic (0% chose this)
C.
Basic with Honours (0% chose this)
D.
Basic and Morse code (0% chose this)

B-002-005-001

What is the correct way to call "CQ" when using Morse code?

A.
Send the letters "CQ" ten times, followed by the word "DE," followed by your call sign once (0% chose this)
B.
Send the letters "CQ" three times, followed by the word "DE," followed by your call sign once (0% chose this)
C.
Send the letters "CQ" until someone answers (0% chose this)
D.
Send the letters "CQ" three times, followed by the word "DE," followed by your call sign three times (100% chose this)

B-006-003-003

Why do most amateur radio antenna systems use coaxial cable, rather than other types of transmission line?

A.
More power handling capability (0% chose this)
B.
Less loss (0% chose this)
C.
More usable in a wide variety of settings (100% chose this)
D.
Less expensive (0% chose this)

B-003-012-003

What is the term for the average power during one RF cycle, at the crest of the modulation envelope?

A.
RMS power (0% chose this)
B.
Peak envelope power (100% chose this)
C.
Peak transmitter input power (0% chose this)
D.
Average radio frequency power (0% chose this)

B-001-011-010

When are you permitted to interfere with another station's transmissions?

A.
When you both wish to contact the same station (0% chose this)
B.
When the other station is interfering with your transmission (0% chose this)
C.
When the other station is not operating in accordance with the Radiocommunication Regulations (0% chose this)
D.
When your station is directly involved with a distress situation (100% chose this)

B-006-009-006

What is the approximate gain of a half-wave dipole in free space relative to an isotropic radiator?

A.
2.1 dB (100% chose this)
B.
3.0 dB (0% chose this)
C.
1.0 dB (0% chose this)
D.
1.5 dB (0% chose this)

B-001-002-001

What must you do within 30 days of a mailing address change?

A.
Inform Radio Amateurs of Canada (RAC) (0% chose this)
B.
Inform Innovation, Science and Economic Development Canada (100% chose this)
C.
Inform your local amateur radio club (0% chose this)
D.
Inform an accredited examiner (0% chose this)

B-002-009-001

What is a "QSL card"?

A.
A notice of an apparent infraction from Innovation, Science and Economic Development Canada (0% chose this)
B.
A postcard reminding you when your certificate will expire (0% chose this)
C.
A letter or postcard from an amateur radio operator (0% chose this)
D.
A written proof of communication between two amateur radio operators (100% chose this)

B-002-006-011

In voice contacts, what is the meaning of "Your signal report is 1 1"?

A.
Your signal is very readable and very strong (0% chose this)
B.
Your signal is 11 dB over S9 (0% chose this)
C.
Your signal is moderately readable with moderate strength (0% chose this)
D.
Your signal is unreadable, and barely perceptible (100% chose this)

B-002-001-011

FM repeater operation on the 2-metre band uses one frequency for transmission and one for reception. What is the standard difference between the transmit and receive frequencies (known as "offset")?

A.
600 kHz (100% chose this)
B.
1000 kHz (0% chose this)
C.
800 kHz (0% chose this)
D.
400 kHz (0% chose this)

B-003-009-004

In a 3-element Yagi antenna, which element is connected to the transmission line?

A.
The boom (0% chose this)
B.
The reflector (0% chose this)
C.
The driven element (100% chose this)
D.
The director (0% chose this)

B-001-010-005

What name is given to a form of interference that seriously degrades, obstructs or repeatedly interrupts a radiocommunication service?

A.
Harmful interference (100% chose this)
B.
Disruptive interference (0% chose this)
C.
Intentional interference (0% chose this)
D.
Adjacent interference (0% chose this)

B-003-007-001

Which of the following is a function of the sound card interface in a station operating computer-based digital modes?

A.
To demodulate the transmitted signal (0% chose this)
B.
To convert the received digital signal from the transceiver into an analog signal for the computer (0% chose this)
C.
To amplify the digital signals to be sent by the transceiver (0% chose this)
D.
To convert the received analog audio signal from the transceiver into a digital signal for the computer (100% chose this)

B-003-015-004

What does "network" mean in packet radio?

A.
The connections on terminal-node controllers (0% chose this)
B.
The programming in a terminal-node controller that rejects other callers if a station is already connected (0% chose this)
C.
A way of connecting packet-radio stations so data can be sent over long distances (100% chose this)
D.
A way of connecting terminal-node controllers by telephone so data can be sent over long distances (0% chose this)

B-001-017-002

For single sideband (SSB) operation, what is the maximum transmitter peak envelope power (PEP) that an amateur radio station may use if the operator holds an Amateur Radio Operator Certificate with Advanced Qualification?

A.
190 watts (0% chose this)
B.
250 watts (0% chose this)
C.
2250 watts (100% chose this)
D.
560 watts (0% chose this)

B-002-001-007

Why should you pause before and between transmissions when using a repeater?

A.
To give the repeater time to respond (0% chose this)
B.
To check the SWR of the repeater (0% chose this)
C.
To reach for pencil and paper for third-party communications (0% chose this)
D.
To listen for anyone else wanting to use the repeater (100% chose this)

B-002-001-010

What is the accepted way to ask someone about their location when using a repeater?

A.
What is your 10-85? (0% chose this)
B.
What is your 10-20? (0% chose this)
C.
Where are you? (100% chose this)
D.
Locations are not normally broadcast over the radio (0% chose this)

B-002-009-010

Your time zone is UTC minus 6 hours. You want to join a net scheduled for 19:00 UTC. What is the local scheduled time?

A.
1 PM (100% chose this)
B.
7 AM (tomorrow) (0% chose this)
C.
7 PM (0% chose this)
D.
1 AM (tomorrow) (0% chose this)

B-001-008-004

What minimum qualifications must an amateur radio operator hold to install a repeater operating on a single band in a voice mode?

A.
Basic and Morse code (0% chose this)
B.
Basic and Advanced (100% chose this)
C.
Basic (0% chose this)
D.
Basic with Honours (0% chose this)

B-001-004-003

Holders of which one of the following certificates may be issued an Amateur Radio Operator Certificate?

A.
Canadian Restricted Operator's Certificate - Maritime Commercial (ROC-MC) (0% chose this)
B.
Canadian Radiocommunication Operator General Certificate Maritime (RGMC) (100% chose this)
C.
Canadian Restricted Operator Certificate - Maritime (ROC-M) (0% chose this)
D.
Canadian Restricted Operator Certificate - Aeronautical (ROC-A) (0% chose this)

B-001-014-008

You and a foreign amateur radio operator both have a local friend without amateur radio certification engaged in radio communication. Who is considered a third party?

A.
The non-certified person at the Canadian station (0% chose this)
B.
Both non-certified persons (100% chose this)
C.
The foreign amateur radio operator and both non-certified persons (0% chose this)
D.
The foreign amateur radio operator and the other person at the foreign station (0% chose this)

B-003-001-006

In an HF station, what device might allow the use of an antenna on a band it was not designed for?

A.
An SWR meter (0% chose this)
B.
A low-pass filter (0% chose this)
C.
A high-pass filter (0% chose this)
D.
An antenna tuner (100% chose this)

B-003-002-001

What does the microphone produce in an FM transmitter?

A.
A radio frequency signal driving the power amplifier (0% chose this)
B.
A radio frequency signal driving the speech amplifier (0% chose this)
C.
An electrical signal driving the oscillator (0% chose this)
D.
An electrical signal driving the speech amplifier (100% chose this)

B-005-009-011

If you wire two 24-microfarad capacitors in parallel, what is the capacity of the combination?

A.
4 microfarads (0% chose this)
B.
12 microfarads (0% chose this)
C.
96 microfarads (0% chose this)
D.
48 microfarads (100% chose this)

B-006-003-006

Which popular RF connector is designed to be moisture resistant?

A.
N (100% chose this)
B.
BNC (0% chose this)
C.
UHF (0% chose this)
D.
SMA (0% chose this)

B-001-013-003

What do you transmit to identify your amateur radio station?

A.
Your full name (0% chose this)
B.
Your call sign (100% chose this)
C.
Your "handle" (0% chose this)
D.
Your first name and your location (0% chose this)

B-001-005-005

What regulatory requirement must be met to allow you to repair an amateur radio transmitter on behalf of another person?

A.
Only you must hold an Amateur Radio Operator Certificate (0% chose this)
B.
Both you and the other person must hold Amateur Radio Operator Certificates (100% chose this)
C.
The other person must be enrolled in an amateur radio certification course (0% chose this)
D.
Only the other person must hold an Amateur Radio Operator Certificate (0% chose this)

B-001-011-008

What is expected of operators NOT directly involved in a disaster relief net?

A.
Limit operation to narrow bandwidth digital modes (0% chose this)
B.
Avoid needless transmissions on or near the net frequency (100% chose this)
C.
Choose another band with a shorter distance reach (0% chose this)
D.
Defer communications until net activity is less intense (0% chose this)

B-004-001-002

If an amplifier becomes non-linear, the output signal would:

A.
be reduced to zero (0% chose this)
B.
overload the power supply (0% chose this)
C.
cause oscillations (0% chose this)
D.
become distorted (100% chose this)

B-001-002-006

What is the fee for a first Amateur Radio Operator Certificate?

A.
$32 (0% chose this)
B.
Free (100% chose this)
C.
$24 (0% chose this)
D.
$10 (0% chose this)

B-001-007-009

The transmission of a secret code by the operator of an amateur radio station:

A.
is not permitted (100% chose this)
B.
is permitted for third-party traffic (0% chose this)
C.
is permitted for contests (0% chose this)
D.
must be approved by Innovation, Science and Economic Development Canada (0% chose this)

B-005-007-003

Why is the range of frequencies from 20 Hz to 20 kHz termed audio frequencies?

A.
Because sound can be in this range but it's too low for RF signals (0% chose this)
B.
Because RF signals in this range can be directly converted to sound (0% chose this)
C.
Because this is the speaker response range of a modern SSB receiver (0% chose this)
D.
Because the human ear can sense sound in this range (100% chose this)

B-001-025-003

When determining the field strength criterion per Electromagnetic Compatibility Advisory Bulletin EMCAB-2, what type of equipment describes devices often used in home entertainment systems, but not strictly speaking radio apparatus?

A.
Low-immunity equipment (0% chose this)
B.
Associated equipment (100% chose this)
C.
Radio-sensitive equipment (0% chose this)
D.
Broadcast receivers (0% chose this)

B-001-025-002

Your neighbour's television receiver malfunctions when you are transmitting. What provision in Electromagnetic Compatibility Advisory Bulletin EMCAB-2 deems your transmission is the cause?

A.
The field strength of your emissions, on your neighbour's premises, is above Innovation, Science and Economic Development Canada's specified immunity criteria (100% chose this)
B.
You are transmitting at or below your maximum permitted power (0% chose this)
C.
The malfunction continues when you stop transmitting (0% chose this)
D.
The field strength of your emissions, on your neighbour's premises, is below Innovation, Science and Economic Development Canada's specified immunity criteria (0% chose this)

B-004-002-001

A diode is in series in the positive power lead to a transceiver. What is its purpose?

A.
Protect against voltage transients (0% chose this)
B.
Overcurrent protection (0% chose this)
C.
Reverse polarity protection (100% chose this)
D.
Permit AC operation (0% chose this)

B-002-007-001

What does the code "QRS" mean in amateur radio?

A.
Send more slowly (100% chose this)
B.
Interference from static (0% chose this)
C.
Send "RST" report (0% chose this)
D.
Radio station location is ... (0% chose this)

B-001-014-002

In what circumstances can foreign amateur radio operators, other than United States citizens, operate while visiting Canada?

A.
Canada automatically grants privileges to visiting amateur radio operators (0% chose this)
B.
Amateur radio operators are automatically granted equivalent privileges in all member states of the International Telecommunication Union (0% chose this)
C.
The foreign amateur radio operator must submit an application to Radio Amateurs of Canada (RAC) (0% chose this)
D.
Their country has an agreement with Canada and the amateur radio operator has obtained the appropriate permit (100% chose this)

B-006-008-010

Some antennas are constructed with traps. What is a trap?

A.
A large wire-wound resistor (0% chose this)
B.
A coil wrapped around a ferrite rod (0% chose this)
C.
A coil and capacitor in parallel (100% chose this)
D.
A hollow metal can (0% chose this)

B-007-001-001

What type of wave propagation usually occurs between two nearby VHF transceivers?

A.
Ionospheric (0% chose this)
B.
Line-of-sight (100% chose this)
C.
Auroral (0% chose this)
D.
Ducting (0% chose this)

B-008-001-001

What is the cause of receiver overload?

A.
Frequency instability of a transmitter (0% chose this)
B.
Overmodulation of a transmitter (0% chose this)
C.
Parasitic oscillations in a transmitter (0% chose this)
D.
Very strong signal from a transmitter (100% chose this)

B-002-006-010

What does "RST 459" mean in a Morse code contact?

A.
Your signal is moderately readable, very weak, and with hum on the tone (0% chose this)
B.
Your signal is quite readable, fair strength, and with perfect tone (100% chose this)
C.
Your signal is barely readable, very weak, and with perfect tone (0% chose this)
D.
Your signal is very readable, very strong, and with perfect tone (0% chose this)

B-002-009-004

A directional antenna pointed in the long-path direction to another station is generally oriented how many degrees from its short-path heading?

A.
180 degrees (100% chose this)
B.
90 degrees (0% chose this)
C.
45 degrees (0% chose this)
D.
270 degrees (0% chose this)

B-001-024-005

According to Safety Code 6, what is the maximum safe power output to the antenna of a hand-held VHF or UHF radio?

A.
7 watts (0% chose this)
B.
5 watts (0% chose this)
C.
Not specified (100% chose this)
D.
8 watts (0% chose this)

B-001-021-003

A Canadian amateur radio operator, operating their station 7 kilometres offshore from the coast of Florida, is subject to which frequency band limits?

A.
Those applicable in International Telecommunication Union region 2 (0% chose this)
B.
Those applicable to United States amateur radio operators (100% chose this)
C.
Those applicable in International Telecommunication Union region 1 (0% chose this)
D.
Those applicable to Canadian amateur radio operators (0% chose this)

B-002-001-006

How do you call another station on a repeater if you know the station's call sign?

A.
Say "break, break," then say the station's call sign (0% chose this)
B.
Wait for the station to call "CQ," then answer it (0% chose this)
C.
Say the station's call sign, then identify your own station (100% chose this)
D.
Say "CQ" three times, then say the station's call sign (0% chose this)

B-002-008-002

You need to summon help while stranded in a remote location, but without immediate risk to life. What priority is your message?

A.
Welfare (0% chose this)
B.
Urgent (100% chose this)
C.
Distress (0% chose this)
D.
Safety (0% chose this)

B-002-002-009

In the International Telecommunication Union phonetic alphabet, what is the code word for the letter L?

A.
London (0% chose this)
B.
Luxembourg (0% chose this)
C.
Love (0% chose this)
D.
Lima (100% chose this)

B-003-012-001

What may happen if an SSB transmitter is operated with the microphone gain set too high?

A.
It may cause interference to other stations operating on lower bands (0% chose this)
B.
It may cause digital interference to computer equipment (0% chose this)
C.
It may cause harmonic interference on higher bands (0% chose this)
D.
It may interfere with other stations operating near its frequency (100% chose this)

B-003-010-010

A communications receiver has four filters installed in it, respectively designated as 250 Hz, 500 Hz, 2.4 kHz and 6 kHz. You are copying a CW transmission and there is a great deal of interference. Which one of the filters would you choose?

A.
250 Hz (100% chose this)
B.
6 kHz (0% chose this)
C.
500 Hz (0% chose this)
D.
2.4 kHz (0% chose this)

B-001-024-008

Which statement is NOT correct?

A.
Hand-held transmitters are excluded from Safety Code 6 requirements (100% chose this)
B.
Safety Code 6 specifies lower exposure limits for the general public in uncontrolled areas than for controlled areas (0% chose this)
C.
Safety Code 6 uses different units for magnetic field strength and electric field strength (0% chose this)
D.
Antenna gain, distance, transmitter power and frequency all influence exposure to radio energy (0% chose this)

B-001-012-002

Radiocommunications transmitted by stations other than a broadcasting station may be divulged or used:

A.
if transmitted in English or French (0% chose this)
B.
if the other station is using digital means (0% chose this)
C.
if it is transmitted by an amateur radio station (100% chose this)
D.
during peacetime civil emergencies (0% chose this)

B-001-017-007

What is the maximum allowed DC input power to the final RF stage of an amateur radio transmitter when the operator holds an Amateur Radio Operator Certificate with Advanced Qualification?

A.
1000 watts (50% chose this)
B.
560 watts (0% chose this)
C.
250 watts (50% chose this)
D.
1500 watts (0% chose this)

B-002-002-005

In the International Telecommunication Union phonetic alphabet, what is the code word for the letter D?

A.
Denmark (0% chose this)
B.
Dog (0% chose this)
C.
Delta (100% chose this)
D.
David (0% chose this)

B-002-006-004

What is the meaning of: "Your signal report is 3 3"?

A.
The station is located at latitude 33 degrees (0% chose this)
B.
Your signal is readable with considerable difficulty and weak in strength (100% chose this)
C.
The contact is serial number 33 (0% chose this)
D.
Your signal is unreadable, very weak in strength (0% chose this)

B-001-004-002

Which examination must be passed before an Amateur Radio Operator Certificate is issued?

A.
A practical test (0% chose this)
B.
Basic Qualification (100% chose this)
C.
Advanced Qualification (0% chose this)
D.
Morse code (0% chose this)

B-003-006-007

In a single-sideband transmitter, which stage allows you to adjust the final transmit frequency?

A.
Sideband filter (0% chose this)
B.
Balanced modulator (0% chose this)
C.
Variable frequency oscillator (100% chose this)
D.
Antenna tuner (0% chose this)

B-003-012-008

How should the microphone gain control be adjusted for voice operation on a single-sideband transmitter?

A.
For 100% frequency deviation on voice peaks (0% chose this)
B.
Such that the maximum range on the ALC meter is never exceeded on voice peaks (100% chose this)
C.
For full deflection of the ALC meter (0% chose this)
D.
For a dip in the drain or collector current (0% chose this)

B-002-001-005

What is a CTCSS tone?

A.
A signal used for radio control of model craft (0% chose this)
B.
A signal used for telemetry by amateur radio satellites (0% chose this)
C.
A tone used by repeaters to mark the end of a transmission (0% chose this)
D.
A sub-audible tone that activates a receiver audio output when present (100% chose this)

B-006-001-010

What factors determine the characteristic impedance of an open-wire transmission line?

A.
The frequency of the signal and the length of the line (0% chose this)
B.
The distance between the centres of the conductors and the length of the line (0% chose this)
C.
The radius of the conductors and the frequency of the signal (0% chose this)
D.
The distance between the centres of the conductors and the diameter of the conductors (100% chose this)

B-001-009-005

When must an amateur radio station have a control operator?

A.
Only when training another amateur radio operator (0% chose this)
B.
A control operator is not needed (0% chose this)
C.
Whenever the station receiver is operated (0% chose this)
D.
Whenever the station is transmitting (100% chose this)

B-001-002-004

The Amateur Radio Operator Certificate:

A.
must be kept in a safe place (0% chose this)
B.
must be kept on the person to whom it is issued (0% chose this)
C.
must be put on file (0% chose this)
D.
must be retained at the station (100% chose this)

B-002-008-004

What is the correct distress signal in Morse code?

A.
SOS (100% chose this)
B.
MAYDAY (0% chose this)
C.
CQD (0% chose this)
D.
QRRR (0% chose this)

B-002-004-008

If propagation changes during your contact and you notice increasing interference from other stations on the same frequency, what should you do?

A.
Tell the interfering stations to change frequency, since you were there first (0% chose this)
B.
Move to another frequency (100% chose this)
C.
Increase your output power (0% chose this)
D.
Report the interference to your Section Manager at Radio Amateurs of Canada (RAC) (0% chose this)

B-006-007-002

What does vertical wave polarization mean?

A.
The electric and magnetic lines of force of a radio wave are parallel to the Earth's surface (0% chose this)
B.
The electric lines of force of a radio wave are perpendicular to the Earth's surface (100% chose this)
C.
The magnetic lines of force of a radio wave are perpendicular to the Earth's surface (0% chose this)
D.
The electric lines of force of a radio wave are parallel to the Earth's surface (0% chose this)

B-002-001-002

What is the main purpose of a repeater?

A.
To link amateur radio stations with the telephone system (0% chose this)
B.
To make local information available 24 hours a day (0% chose this)
C.
To increase the range of portable and mobile stations (100% chose this)
D.
To retransmit weather information during severe storm warnings (0% chose this)

B-002-004-010

What is a band plan?

A.
A voluntary division of an amateur radio band to avoid interference between incompatible modes (100% chose this)
B.
A schedule of operating restrictions within a band prescribed by Innovation, Science and Economic Development Canada (0% chose this)
C.
A schedule of additional band allocations for recommendation to the International Telecommunication Union (0% chose this)
D.
A plan devised by a club for the effective use of a frequency band during a contest (0% chose this)

B-003-010-011

When receiving CW, which of these frequency ranges is optimum for a band-pass filter?

A.
100 Hz to 1100 Hz (0% chose this)
B.
300 Hz to 2700 Hz (50% chose this)
C.
2100 Hz to 2300 Hz (0% chose this)
D.
750 Hz to 850 Hz (50% chose this)

B-003-002-003

An FM transmitter's modulator:

A.
alters the radio's output signal amplitude (0% chose this)
B.
as no effect on the frequency of the oscillator (0% chose this)
C.
affects the frequency of the oscillator (100% chose this)
D.
produces amplitude changes in the oscillator (0% chose this)

B-002-002-002

What can you use as an aid for correct station identification when using voice?

A.
Unique words of your choice (0% chose this)
B.
A speech compressor (0% chose this)
C.
Q codes (0% chose this)
D.
The International Telecommunication Union phonetic alphabet (100% chose this)

B-003-010-001

Which series of emission modes listed below is in order from the narrowest bandwidth to the widest bandwidth?

A.
CW, FM voice and SSB voice (0% chose this)
B.
FM voice, SSB voice and CW (0% chose this)
C.
SSB voice, CW and FM voice (0% chose this)
D.
CW, SSB voice and FM voice (100% chose this)

B-002-007-004

What does the code "QSY" mean in amateur radio?

A.
Send faster (0% chose this)
B.
Change frequency (100% chose this)
C.
Use more power (0% chose this)
D.
Send more slowly (0% chose this)

B-001-021-006

A CEPT (European Conference of Postal and Telecommunications Administrations) Amateur Radio Licence allows a qualified Canadian amateur radio operator to operate while visiting any participating country. What minimum level of qualification does a Canadian amateur radio operator need?

A.
Advanced (100% chose this)
B.
Basic with Morse code (0% chose this)
C.
Basic with Honours (0% chose this)
D.
Basic (0% chose this)

B-005-006-003

What is the DC input power of a transmitter operating at 12 volts and drawing 500 milliamperes?

A.
24 watts (0% chose this)
B.
600 watts (0% chose this)
C.
6 watts (100% chose this)
D.
60 watts (0% chose this)

B-002-007-005

What does the code "QSB" mean in amateur radio?

A.
Your signal is fading (100% chose this)
B.
I am confirming contact (0% chose this)
C.
I am busy (0% chose this)
D.
I have no message (0% chose this)

B-002-009-003

While making a contact in a VHF contest, the other operator asks for your grid square. What information is requested?

A.
The number of contacts you have made (0% chose this)
B.
Your location expressed as a 4 or 6-character code (100% chose this)
C.
Your antenna azimuth stated in compass degrees (0% chose this)
D.
The elevation of your station in thirty-metre increments (0% chose this)

B-001-016-010

Based on the frequency stated and emission mode, which of the following combinations is prohibited?

A.
Single sideband (SSB) on 3.76 MHz (0% chose this)
B.
Fast-scan television (ATV) on 14.23 MHz (100% chose this)
C.
Slow-scan television (SSTV) on 14.23 MHz (0% chose this)
D.
Frequency modulation (FM) on 29.60 MHz (0% chose this)

B-008-003-008

What should you do if you learn your transmitter is producing key clicks?

A.
Check the keying filter and the functioning of later stages (100% chose this)
B.
Use a choke in the RF power output (0% chose this)
C.
Regulate the oscillator supply voltage (0% chose this)
D.
Adjust your key (0% chose this)

B-001-009-009

Under what circumstances can a person who does NOT have an Amateur Radio Operator Certificate operate an amateur radio station?

A.
When the person is under supervision, and in the presence of, a person holding appropriate qualifications (100% chose this)
B.
When the person has been briefed over the telephone by a person holding appropriate qualifications (0% chose this)
C.
When the person is actively enrolled in an amateur radio course (0% chose this)
D.
When the person holds a valid licence in the land mobile or maritime services (0% chose this)

B-001-025-004

Your neighbour complains that your transmissions interfere with their garage door opener. When determining the applicable field strength criterion in Electromagnetic Compatibility Advisory Bulletin EMCAB-2, what type of equipment is the garage door opener?

A.
Associated equipment (0% chose this)
B.
Radio-sensitive equipment (100% chose this)
C.
Broadcast equipment (0% chose this)
D.
Low-immunity equipment (0% chose this)

B-002-004-007

If a net is about to begin on a frequency that you and another station are using, what should you do?

A.
Increase your power output to ensure that all net participants can hear you (0% chose this)
B.
Transmit as long as possible on the frequency so that no other stations may use it (0% chose this)
C.
Turn off your radio (0% chose this)
D.
As a courtesy, move to a different frequency (100% chose this)

B-001-021-009

A Canadian amateur radio operator is operating in the United States using voice. What form of identification is required?

A.
Transmit their Canadian call sign (0% chose this)
B.
Transmit their Canadian call sign, followed by "portable" or "mobile" as appropriate, followed by the prefix for the US call area being visited (100% chose this)
C.
Transmit the prefix for the US call area being visited, followed by "portable" or "mobile" as appropriate, followed by their Canadian call sign (0% chose this)
D.
Transmit their Canadian call sign, followed by the city and state where they are visiting (0% chose this)

B-003-014-010

What is the function of transmit/receive switching in a transceiver?

A.
To prevent RF currents entering the transmitter circuits (0% chose this)
B.
To change antennas for operation on other frequencies (0% chose this)
C.
To allow more than one transmitter to be used (0% chose this)
D.
To enable one antenna to be used for both transmitting and receiving (100% chose this)

B-002-006-009

What does "RST 579" mean in a Morse code contact?

A.
Your signal is perfectly readable, moderately strong, and with perfect tone (100% chose this)
B.
Your signal is barely readable, moderately strong, and with a faint ripple (0% chose this)
C.
Your signal is fairly readable, fair strength, and with perfect tone (0% chose this)
D.
Your signal is perfectly readable, weak strength, and with perfect tone (0% chose this)

B-002-008-001

When may you use your amateur radio station to transmit an "SOS" or "MAYDAY"?

A.
In a life-threatening distress situation (100% chose this)
B.
Only in case of a severe weather watch (0% chose this)
C.
Only at specific times (at 15 and 30 minutes after the hour) (0% chose this)
D.
Never (0% chose this)

B-001-003-001

Transmissions outside of amateur radio bands:

A.
are permitted when using less than 1 watt (0% chose this)
B.
are prohibited and penalties could be assessed to the control operator (100% chose this)
C.
must be identified with your call sign (0% chose this)
D.
are permitted for short tests only (0% chose this)

B-001-007-010

An amateur radio operator may be engaged in communications including the transmission of:

A.
programming that originates from a broadcasting undertaking (0% chose this)
B.
Q codes (100% chose this)
C.
radiocommunication in support of industrial, business, or professional activities (0% chose this)
D.
commercially recorded material (0% chose this)

B-002-001-008

Why should you keep transmissions short when using a repeater?

A.
To reduce the bandwidth used by the repeater (0% chose this)
B.
To avoid exceeding the repeater's memory storage (0% chose this)
C.
To keep long-distance charges down (0% chose this)
D.
A long transmission may prevent someone with an emergency from using the repeater (100% chose this)

B-001-024-010

Which of these statements about Safety Code 6 is NOT correct?

A.
Safety Code 6 sets limits for allowable rates at which RF energy is absorbed in the body (specific absorption rate) (0% chose this)
B.
Safety Code 6 sets limits for contact currents that could be drawn from ungrounded or poorly grounded objects (0% chose this)
C.
Safety Code 6 sets limits for induced currents, electrical field strength and magnetic field strength from electromagnetic radiation (0% chose this)
D.
Safety Code 6 sets limits in terms of power levels fed into antennas (100% chose this)

B-002-009-008

What is the most useful function of an azimuthal world map centred on your location?

A.
To show the azimuth to meteor showers throughout the year (0% chose this)
B.
To associate distances with optimal ionospheric region (0% chose this)
C.
To show the bearing to any location (100% chose this)
D.
To allow computing the radiation angle to any location (0% chose this)

B-002-007-011

What is the Q code that means "I will call you again" in amateur radio?

A.
QRT (0% chose this)
B.
QRS (0% chose this)
C.
QRX (100% chose this)
D.
QRZ (0% chose this)

B-001-013-001

Which of the following call signs is a valid Canadian amateur radio call sign?

A.
VA3RAC (100% chose this)
B.
SM2CAN (0% chose this)
C.
KA9OLS (0% chose this)
D.
BY7HY (0% chose this)

B-001-007-006

When may an amateur radio station transmit an encoded message?

A.
Only when transmitting above 450 MHz (0% chose this)
B.
Only during contests (0% chose this)
C.
Only when the encoding or cipher is not secret (100% chose this)
D.
Only during a declared communications emergency (0% chose this)

B-001-010-008

Amateur radio operations are NOT protected from interference caused by another service operating in which of the following frequency bands?

A.
902 MHz to 928 MHz (100% chose this)
B.
222 MHz to 225 MHz (0% chose this)
C.
144 MHz to 148 MHz (0% chose this)
D.
50 MHz to 54 MHz (0% chose this)

B-001-008-006

What minimum qualifications must an amateur radio operator hold to install or operate a transmitter or RF amplifier that is neither professionally designed nor commercially manufactured for use in the amateur radio service?

A.
Basic and Advanced (100% chose this)
B.
Basic, Advanced and Morse code (0% chose this)
C.
Basic with Honours (0% chose this)
D.
Basic and Morse code (0% chose this)

B-001-007-001

Which of the following topics is prohibited on an amateur radio club net?

A.
Recreation planning (0% chose this)
B.
Business planning (100% chose this)
C.
Emergency planning (0% chose this)
D.
Code practice planning (0% chose this)

B-008-002-001

What devices would you install to reduce or eliminate interference to a home entertainment system from an HF transmitter?

A.
Metal oxide varistors (0% chose this)
B.
Bypass inductors (0% chose this)
C.
Coils on ferrite cores (100% chose this)
D.
Bypass resistors (0% chose this)

B-002-006-005

What is the meaning of: "You are 5 9 plus 20 dB"?

A.
You are perfectly readable with a signal strength 20 decibels greater than S9 (100% chose this)
B.
Your signal strength has increased by a factor of 100 (0% chose this)
C.
The bandwidth of your signal is 20 decibels above linearity (0% chose this)
D.
Repeat your transmission on a frequency 20 kHz higher (0% chose this)

B-001-017-001

What transmitter power should Canadian amateur radio operators use at all times?

A.
560 watts DC input (0% chose this)
B.
400 watts PEP output (0% chose this)
C.
The minimum legal power necessary to communicate (100% chose this)
D.
560 watts PEP output (0% chose this)

B-001-010-009

Under what circumstances may the operator of an amateur radio station conduct test transmissions?

A.
When transmitting in designated sub-bands (0% chose this)
B.
When the transmission will not cause interference to stations in the amateur radio service or other services (100% chose this)
C.
After warning other stations who might be interfered with (0% chose this)
D.
Only between the hours of midnight and 8:00 AM (0% chose this)

B-001-020-002

The amateur radio station operator shall ensure that:

A.
international communications are limited to the purposes of amateur radio or remarks of a personal nature (100% chose this)
B.
international communications are carried out within the power limitations of the foreign administration (0% chose this)
C.
commercial communications are brief (0% chose this)
D.
third parties are charged a nominal sum for their messages (0% chose this)

B-001-011-009

When may amateur radio operators handle messages from recognized public service agencies?

A.
During peace time, civil emergencies and exercises (100% chose this)
B.
When data modes are used exclusively (0% chose this)
C.
When operators have an Advanced Qualification (0% chose this)
D.
When special authorization has been obtained from Innovation, Science and Economic Development Canada (0% chose this)

B-007-004-003

A radio transmission may follow two or more different paths during propagation, and this may result in phase differences at the receiver. What is the effect at the receiver?

A.
Intermodulation (0% chose this)
B.
Absorption (0% chose this)
C.
Fading (100% chose this)
D.
Wavering (0% chose this)

B-002-007-009

What is the Q code indicating that you want the other station to send slower?

A.
QRS (100% chose this)
B.
QRM (0% chose this)
C.
QRL (0% chose this)
D.
QRN (0% chose this)

B-001-001-004

Which document defines the Canadian "amateur radio service"?

A.
The Radio Systems Policies (0% chose this)
B.
The Standards for the Operation of Radio Stations in the Amateur Radio Service (0% chose this)
C.
The Radiocommunication Act (0% chose this)
D.
The Radiocommunication Regulations (100% chose this)

B-003-002-004

How is the oscillator in the FM transmitter different from oscillators in AM, CW, and SSB transmitters?

A.
The modulator changes its output amplitude (0% chose this)
B.
The modulator alters its frequency (100% chose this)
C.
It has higher fidelity (0% chose this)
D.
It runs at much higher frequencies (0% chose this)

B-003-005-008

In an SSB/CW receiver, what is the purpose of the signal produced by the beat frequency oscillator (BFO)?

A.
It is fed to the receiver input to provide band edge markers (0% chose this)
B.
It drives the automatic gain control circuit to maintain a constant audio level (0% chose this)
C.
It is mixed with the IF to recover the transmitted modulation (100% chose this)
D.
It is mixed with the incoming signal to produce the intermediate frequency (0% chose this)

B-003-010-004

What is the function of automatic gain control (AGC) in a receiver?

A.
Maximize overall gain for greater sensitivity (0% chose this)
B.
Limit the change in volume due to large signal strength variations (100% chose this)
C.
Remove high-amplitude short-duration noise pulses (0% chose this)
D.
Improve the signal-to-distortion ratio of the detector (0% chose this)

B-001-011-002

During relief operations in the days following a disaster, when may you use your amateur radio equipment to communicate on frequencies outside amateur radio bands?

A.
When messages are destined to agencies without amateur radio support (0% chose this)
B.
When relaying messages on behalf of government agencies (0% chose this)
C.
Using frequencies outside amateur radio bands is never permitted (100% chose this)
D.
When normal communication systems are overloaded, damaged or disrupted (0% chose this)

B-001-017-005

For SSB operation on 7055 kHz, what is the maximum transmitter peak envelope power (PEP) that an amateur radio station may use if the operator holds an Amateur Radio Operator Certificate with Basic Qualification with Honours?

A.
560 watts (100% chose this)
B.
2250 watts (0% chose this)
C.
1000 watts (0% chose this)
D.
200 watts (0% chose this)

B-001-007-008

What should you do to keep your amateur radio station from retransmitting music or signals from a non-amateur radio station?

A.
Adjust your transceiver noise blanker (0% chose this)
B.
Speak closer to the microphone to increase your signal strength (0% chose this)
C.
Turn up the volume of your transmitter (0% chose this)
D.
Turn down the volume of background audio (100% chose this)

B-007-008-009

Meteor scatter is most effective on what band?

A.
40 metres (0% chose this)
B.
6 metres (100% chose this)
C.
160 metres (0% chose this)
D.
15 metres (0% chose this)

B-002-008-007

In an emergency, what additional equipment is crucial to maintaining communications with a hand-held radio?

A.
An extra antenna (0% chose this)
B.
A portable amplifier (0% chose this)
C.
An adequate supply of charged batteries (100% chose this)
D.
A microphone headset for hands-free operation (0% chose this)

B-003-006-005

In a single-sideband transmitter, what is the purpose of the speech amplifier?

A.
Amplify the audio you wish to transmit (100% chose this)
B.
Amplify one of the signal's two sidebands (0% chose this)
C.
Amplify the signal's harmonic content (0% chose this)
D.
Amplify the signal's carrier (0% chose this)

B-001-024-009

Safety Code 6 sets limits for RF exposure from radio transmitters. Which types of transmitters are exempt from regulation?

A.
No transmitters are exempt (100% chose this)
B.
Broadcast transmitters (0% chose this)
C.
Portable transmitters (0% chose this)
D.
Low power transmitters (less than 10 watts) (0% chose this)

B-001-003-005

Which of the following is NOT correct? The Minister of Innovation, Science and Industry may suspend an Amateur Radio Operator Certificate:

A.
where the holder has contravened the Radiocommunication Act, its regulations, or the terms and conditions of the certificate (0% chose this)
B.
with no notice, or opportunity to make representations thereto (100% chose this)
C.
where the holder has failed to comply with a request to pay fees or interest due (0% chose this)
D.
where the certificate was obtained through misrepresentation (0% chose this)

B-001-006-006

Some VHF and UHF FM radios purchased for use in the amateur radio service can also be programmed to communicate on frequencies used for the land mobile service. Under what conditions is this permissible?

A.
The equipment is used in remote areas north of 60 degrees latitude (0% chose this)
B.
The equipment has an RF power output of 2 watts or less (0% chose this)
C.
The radio operator has a Restricted Operator's Certificate (0% chose this)
D.
The radio is certified and licensed for use in the land mobile service (100% chose this)

B-002-003-008

If you are operating simplex on a repeater frequency, why would it be good practice to change to another frequency?

A.
Because changing the repeater's frequency requires the authorization of Innovation, Science and Economic Development Canada (0% chose this)
B.
Because you may interfere with users of the repeater (100% chose this)
C.
Because the repeater's output power may overload your receiver (0% chose this)
D.
Because there are more repeater operators than simplex operators (0% chose this)

B-001-006-004

When is it permissible to use amateur radio equipment, with or without modification, to transmit outside amateur radio bands?

A.
When the control operator holds an Advanced Qualification (0% chose this)
B.
When transmissions are limited to licence-exempt frequencies (0% chose this)
C.
When the operator already owns licensed equipment for such frequencies (0% chose this)
D.
Never, amateur radio equipment is not certified for operation outside amateur radio bands (100% chose this)

B-001-024-001

What organization has published safety guidelines for the maximum limits of RF energy near the human body?

A.
Health Canada (100% chose this)
B.
National Research Council (0% chose this)
C.
Environment Canada (0% chose this)
D.
Canadian Standards Association (0% chose this)

B-001-010-001

What is a transmission that disturbs other communications called?

A.
Unidentified transmissions (0% chose this)
B.
Interrupted CW (0% chose this)
C.
Harmful interference (100% chose this)
D.
Transponder signals (0% chose this)

B-001-009-007

Why can't family members without qualifications transmit using your amateur radio station if they are alone with your equipment?

A.
They must not use your equipment without your permission (0% chose this)
B.
They must first know the right frequencies and emission modes for transmitting (0% chose this)
C.
They must first know how to use the right abbreviations and Q signals (0% chose this)
D.
They must hold suitable amateur radio qualifications before they are allowed to be control operators (100% chose this)

B-001-008-003

What minimum qualifications must an amateur radio operator hold to assemble commercially available transmitter kits of professional design?

A.
Basic and Advanced (0% chose this)
B.
Basic with Honours (0% chose this)
C.
Basic (100% chose this)
D.
Basic and Morse code (0% chose this)

B-001-019-002

Which of the following emission modes requires that an amateur radio station have means to prevent or indicate overmodulation?

A.
RTTY (0% chose this)
B.
SSB (100% chose this)
C.
CW (0% chose this)
D.
FM (0% chose this)

B-001-013-008

What language may you use when identifying your station?

A.
Any language of a country that is a member of the International Telecommunication Union (0% chose this)
B.
Any language being used for a contact, providing Canada has a third-party communications agreement with that country (0% chose this)
C.
English or French (100% chose this)
D.
Any language being used for a contact (0% chose this)

B-001-004-005

What sending and receiving speed, in words per minute (wpm), must you achieve to be granted the Morse code Qualification?

A.
5 wpm (100% chose this)
B.
7 wpm (0% chose this)
C.
12 wpm (0% chose this)
D.
15 wpm (0% chose this)

B-001-008-002

Which type of station may transmit one-way communications?

A.
HF station (0% chose this)
B.
Repeater station (0% chose this)
C.
Beacon station (100% chose this)
D.
VHF station (0% chose this)

B-002-001-001

What is an appropriate way to make contact on a repeater?

A.
Say, "breaker, breaker" (0% chose this)
B.
Say the call sign of the station you want to contact three times (0% chose this)
C.
Say the call sign of the station you want to contact, then your call sign (100% chose this)
D.
Say the other operator's name, then your call sign three times (0% chose this)

B-001-013-009

The call sign of an amateur radio station must be transmitted:

A.
at intervals not greater than three minutes when using voice communications (0% chose this)
B.
at the beginning and at the end of each contact and at intervals not greater than 30 minutes (100% chose this)
C.
when requested to do so by the station being called (0% chose this)
D.
at intervals not greater than ten minutes when using digital modes (0% chose this)

B-001-011-005

An amateur radio operator in distress may:

A.
use any means of radiocommunication (100% chose this)
B.
only use bands for which the operator is authorized (0% chose this)
C.
only use Morse code communications on internationally recognized emergency channels (0% chose this)
D.
use any means of radiocommunication, but only on internationally recognized emergency channels (0% chose this)

B-001-003-008

Interfering with, or obstructing any radio communication, without lawful cause, is prohibited. The person found guilty is liable to what penalty?

A.
A fine, not exceeding $5 000, or a prison term not exceeding one year, or both (100% chose this)
B.
A fine not exceeding $1 000 (0% chose this)
C.
A prison term of two years (0% chose this)
D.
A fine of $10 000 (0% chose this)

B-001-012-004

With regard to divulging the content of radiocommunications other than broadcasting, which of the following is an offence?

A.
Where it is on behalf of Canada, for the purpose of national defence or security (0% chose this)
B.
Where it is for the purpose of giving evidence in a criminal or civil court (0% chose this)
C.
Where it is for the purpose of answering questions from a media organization (100% chose this)
D.
Where it is for the purpose of protecting property or preventing harm (0% chose this)

B-001-015-010

What is the frequency range of the 10-metre amateur radio band in Canada?

A.
21.000 MHz to 21.450 MHz (0% chose this)
B.
24.890 MHz to 24.990 MHz (0% chose this)
C.
28.000 MHz to 29.700 MHz (100% chose this)
D.
50.000 MHz to 54.000 MHz (0% chose this)

B-001-023-004

If an amateur radio operator wants to install or modify an antenna system and the local land-use authority has no approval process, what must the amateur radio operator do?

A.
Develop their own public consultation process (0% chose this)
B.
Wait for the land-use authority to develop its own public consultation process (0% chose this)
C.
Follow the default public consultation process outlined by Innovation, Science and Economic Development Canada (100% chose this)
D.
Proceed without public consultation (0% chose this)

B-001-003-006

Which of the following statements is NOT correct?

A.
A radio inspector may enter a dwelling without the consent of the occupant and without a warrant (100% chose this)
B.
In executing a warrant, a radio inspector shall not use force, unless accompanied by a peace officer, and force is authorized (0% chose this)
C.
Where entry is refused, and is necessary to perform their duties under the Radiocommunication Act, a radio inspector may obtain a warrant (0% chose this)
D.
The person responsible for a dwelling entered by a radio inspector shall provide the inspector the requested information (0% chose this)

B-001-004-001

How old must you be to hold an Amateur Radio Operator Certificate with Basic Qualification?

A.
14 years or older (0% chose this)
B.
18 years or older (0% chose this)
C.
70 years or younger (0% chose this)
D.
There are no age limits (100% chose this)

B-003-004-005

In a basic CW transmitter, what does the power amplifier stage do?

A.
It increases the transmitter's output power (100% chose this)
B.
It reduces distortion in the transmitted signal (0% chose this)
C.
It multiplies the oscillator frequency to the operating frequency (0% chose this)
D.
It removes CW chirps from the transmitted signal (0% chose this)

B-005-009-004

If two equal-value capacitors are connected in parallel, what is their total capacitance?

A.
The value of one capacitor times 4 (0% chose this)
B.
Twice the value of one capacitor (100% chose this)
C.
Half the value of either capacitor (0% chose this)
D.
The value of one capacitor divided by 4 (0% chose this)

B-002-002-010

In the International Telecommunication Union phonetic alphabet, what is the code word for the letter P?

A.
Peter (0% chose this)
B.
Portugal (0% chose this)
C.
Paris (0% chose this)
D.
Papa (100% chose this)

B-001-004-007

What conditions must candidates for amateur radio certification meet?

A.
Be at least 14 years of age and a Canadian citizen or permanent resident (0% chose this)
B.
Be a Canadian citizen (0% chose this)
C.
Be a Canadian citizen or permanent resident (0% chose this)
D.
Have a valid address in Canada (100% chose this)

B-001-002-007

The Amateur Radio Operator Certificate should be:

A.
retained on the holder's person (0% chose this)
B.
retained in the holder's vehicle (0% chose this)
C.
retained in a safety deposit box (0% chose this)
D.
retained at the address provided to Innovation, Science and Economic Development Canada (100% chose this)

B-001-010-004

What rule applies if two amateur radio operators want to use the same frequency?

A.
The station operator with a lesser qualification must yield the frequency to an operator of higher qualification (0% chose this)
B.
Both station operators have an equal right to operate on the frequency (100% chose this)
C.
Station operators in regions 1 and 3 of the International Telecommunication Union must yield the frequency to stations in region 2 (0% chose this)
D.
The station operator with a lower power output must yield the frequency to the station with a higher power output (0% chose this)

B-001-005-001

Under what circumstances can an amateur radio operator with an Advanced Qualification install, place in operation, modify or repair radio apparatus on behalf of another person?

A.
Pending the granting of an Amateur Radio Operator Certificate if the apparatus covers amateur radio bands only (0% chose this)
B.
If the other person holds an authorization for this apparatus (100% chose this)
C.
Pending the granting of an authorization if the apparatus is certified and crystal controlled (0% chose this)
D.
Pending the granting of a radio authorization, if the apparatus covers amateur radio and commercial bands (0% chose this)

B-001-003-004

Which government document states the offences and penalties relating to radiocommunications?

A.
The Radiocommunication Act (100% chose this)
B.
The Radio Systems Policies (0% chose this)
C.
The Radiocommunications Regulations (0% chose this)
D.
The Broadcasting Act (0% chose this)

B-003-003-009

In a receiver, which stage is controlled by the volume control?

A.
Discriminator (0% chose this)
B.
IF amplifier (0% chose this)
C.
Limiter (0% chose this)
D.
AF amplifier (100% chose this)

B-003-011-011

The difference between DC input power and RF output power of a transmitter RF amplifier:

A.
is lost in the transmission line (0% chose this)
B.
appears as heat (100% chose this)
C.
is due to oscillations (0% chose this)
D.
radiates from the antenna (0% chose this)

B-001-002-005

A radio inspector asks to see your Amateur Radio Operator Certificate, or a copy thereof. Per the regulations, how many hours are you given to comply?

A.
12 (0% chose this)
B.
72 (0% chose this)
C.
24 (0% chose this)
D.
48 (100% chose this)

B-001-014-010

While in Canada and operating in a voice mode, American amateur radio operators must identify with their call sign, the qualifier "mobile" or "portable" and what other information?

A.
The transmitting frequency being used (0% chose this)
B.
The Canadian call sign prefix for the geographic location of the station (100% chose this)
C.
The name of the nearest Canadian community (0% chose this)
D.
The name of the province or territory where the station is located (0% chose this)

B-002-009-009

Activity schedules, time entries in logbooks and contact confirmations usually refer to UTC (Coordinated Universal Time). What is the location of the meridian from which this time is measured?

A.
Geneva, Switzerland (0% chose this)
B.
Ottawa, Canada (0% chose this)
C.
Greenwich, United Kingdom (100% chose this)
D.
Boulder, United States of America (0% chose this)

B-001-017-004

For SSB operation on 3750 kHz, what is the maximum transmitter peak envelope power (PEP) that an amateur radio station may use if the operator holds an Amateur Radio Operator Certificate with Basic and Morse code qualifications?

A.
1000 watts (0% chose this)
B.
560 watts (100% chose this)
C.
2250 watts (0% chose this)
D.
1500 watts (0% chose this)

B-001-022-003

What is the fee for taking an examination for an Amateur Radio Operator Certificate, administered by an accredited examiner?

A.
The examiner may charge a fee to recover costs (67% chose this)
B.
No fee may be charged (33% chose this)
C.
$20 per examination sitting (0% chose this)
D.
$20 per qualification (0% chose this)

B-001-013-011

The call sign of a Canadian amateur radio station would normally start with the letters:

A.
VA, VE, VO or VY (100% chose this)
B.
GA, GE, MO or VQ (0% chose this)
C.
A, K, N or W (0% chose this)
D.
EA, EI, RO or UY (0% chose this)

B-001-010-010

Which of these amateur radio bands may be heavily occupied by licence-exempt devices?

A.
135.7 kHz to 137.8 kHz (0% chose this)
B.
3.5 MHz to 4.0 MHz (0% chose this)
C.
430 MHz to 450 MHz (0% chose this)
D.
902 MHz to 928 MHz (100% chose this)

B-001-023-001

Which of these statements about the installation or modification of an antenna structure is NOT correct?

A.
Innovation, Science and Economic Development Canada expects amateur radio operators to address community concerns in a responsible manner (0% chose this)
B.
An amateur radio operator may erect any size antenna structure without consulting neighbours or the local land-use authority (100% chose this)
C.
Prior to an installation, for which community concerns could be raised, amateur radio operators may be required to consult with their land-use authority (0% chose this)
D.
An amateur radio operator must follow Innovation, Science and Economic Development Canada's antenna siting procedures (0% chose this)

B-001-013-004

What identification, if any, is required when two amateur radio stations begin communications?

A.
No identification is required (0% chose this)
B.
One of the stations must give both stations' call signs (0% chose this)
C.
Both stations must transmit both call signs (33% chose this)
D.
Each station must transmit its own call sign (67% chose this)

B-001-003-003

Transmitting a false or fraudulent distress signal or message is prohibited. The person found guilty is liable to what penalty?

A.
A fine of $10 000 (0% chose this)
B.
A fine not exceeding $1 000 (0% chose this)
C.
A prison term of two years (0% chose this)
D.
A fine, not exceeding $5 000, or a prison term not exceeding one year, or both (100% chose this)

B-001-023-010

Where a land-use authority or municipality has established a public consultation process for antenna systems, who determines how public consultation should take place?

A.
The municipality or local land-use authority (100% chose this)
B.
The provincial government (0% chose this)
C.
Innovation, Science and Economic Development Canada (0% chose this)
D.
The person planning to erect an antenna structure (0% chose this)

B-002-004-003

You need to transmit to adjust your antenna tuner prior to joining an HF single-sideband net that is in progress. On what frequency should you make the adjustment?

A.
3 kHz to 5 kHz away from the net frequency (100% chose this)
B.
On the net frequency (0% chose this)
C.
On the band's centre frequency (0% chose this)
D.
1 kHz away from the net frequency (0% chose this)

B-001-022-005

Which of the following statements is NOT correct?

A.
A candidate who fails a written examination due to not usually speaking English or French may be given an oral examination (0% chose this)
B.
A candidate with insufficient knowledge of English or French may be accompanied by an interpreter (100% chose this)
C.
An examiner may request medical evidence from a practising medical physician before accommodating testing (0% chose this)
D.
A candidate who fails a written examination for lack of reading skills may be given an oral examination (0% chose this)

B-001-013-005

What identification, if any, is required when two amateur radio stations end communications?

A.
No identification is required (0% chose this)
B.
Both stations must transmit both call signs (0% chose this)
C.
One of the stations must transmit both stations' call signs (0% chose this)
D.
Each station must transmit its own call sign (100% chose this)

B-001-003-002

What is the term in the regulations that defines if an amateur radio operator falsely transmits the word "MAYDAY" when there isn't an emergency?

A.
An emergency test transmission (0% chose this)
B.
An encrypted message (0% chose this)
C.
A privileged communication (0% chose this)
D.
A false or fraudulent message (100% chose this)

B-001-025-001

Your neighbour's stereo system malfunctions when you are transmitting. What provision in Electromagnetic Compatibility Advisory Bulletin EMCAB-2 deems the stereo system's lack of immunity is the cause?

A.
The field strength of your emissions, on your neighbour's premises, is below Innovation, Science and Economic Development Canada's specified immunity criteria (100% chose this)
B.
The field strength of your emissions, on your neighbour's premises, is above Innovation, Science and Economic Development Canada's specified immunity criteria (0% chose this)
C.
You are transmitting at or below your maximum permitted power (0% chose this)
D.
The malfunction stops when you stop transmitting (0% chose this)

B-002-005-011

What is the meaning of the Morse code signal "R"?

A.
Called station only reply (0% chose this)
B.
All received (100% chose this)
C.
Repeat all (0% chose this)
D.
End of message (0% chose this)

B-001-015-003

In addition to passing the Basic written examination, what must you do before you are allowed to use amateur radio frequencies below 30 MHz?

A.
You must attain a mark of 80% on the Basic examination, or pass an Advanced or Morse code examination (100% chose this)
B.
You must attend a class to learn about HF communications (0% chose this)
C.
You must notify Innovation, Science and Economic Development Canada that you intend to operate on the HF bands (0% chose this)
D.
You must pass a provincial communications examination (0% chose this)

B-001-020-005

Canadian amateur radio operators must comply with the Radiocommunication Act and Radiocommunication Regulations. What other organization issues radio regulations that Canadian amateur radio operators must comply with?

A.
Provincial or territorial government communications department (0% chose this)
B.
International Amateur Radio Union (0% chose this)
C.
Radio Amateurs of Canada (RAC) (0% chose this)
D.
International Telecommunication Union (100% chose this)

B-001-003-007

When is an amateur radio operator permitted to transmit false information?

A.
Transmitting false information is never permitted (100% chose this)
B.
To conceal their identity when responding to inappropriate on-air conduct (0% chose this)
C.
To exaggerate the scope of an emergency to obtain help more rapidly (0% chose this)
D.
To play a practical joke, for example, giving incorrect location of an amateur radio event (0% chose this)

B-001-001-003

Which department is responsible for the administration of the Radiocommunication Act?

A.
National Defence (0% chose this)
B.
Communications Security Establishment Canada (0% chose this)
C.
Innovation, Science and Economic Development Canada (100% chose this)
D.
Transport Canada (0% chose this)

B-001-018-002

An unmodulated carrier may be transmitted only:

A.
for holding a frequency until a net begins (0% chose this)
B.
if the final RF amplifier output is kept under 5 watts (0% chose this)
C.
for brief tests on frequencies below 30 MHz (100% chose this)
D.
for CW communication (0% chose this)

B-001-021-005

In which region of the International Telecommunication Union are Europe and Africa located?

A.
Region 1 (100% chose this)
B.
Region 2 (0% chose this)
C.
Region 4 (0% chose this)
D.
Region 3 (0% chose this)

Log in

- or -

- or -