Impedance is the opposition to the flow of current in an AC circuit. Impedance is composed of resistance and reactance (both capacitive and inductive).

Note: Think that "impedance" is going to "impede" or get in the way of current flow.

For more info see Wikipedia: Electrical Impedance

SILLY HINT: The correct choice is the only one with VOLTAGE following OF in the wording.

Last edited by kd7bbc. Register to edit

Tags: none

(B). Reactance is the opposition to the flow of alternating current caused by capacitance or inductance. Reactance changes with both the capacitance and inductance of the current to act along with resistance as components of the impedance.

Note: Reactance (either from changes in capacitance and/or inductance) is going to make the circuit "react" and block (oppose) current flow in the AC circuit.

Hint: Reactance includes the letters "AC"

For more info see Wikipedia: Reactance

Last edited by malibu. Register to edit

Tags: none

(D). Reactance is the factor listed which causes opposition to the flow of alternating current (AC) in an inductor. Both inductive (from an inductor) and capacitive (from a capacitor) reactances act with resistance to oppose the flow of current as components of impedance.

For more info see Wikipedia: Electrical Reactance, Inductor

Last edited by edward@rfreduce.com. Register to edit

Tags: none

(C). The Reactance is the factor which causes opposition to the flow of alternating current (AC) in a capacitor. Both capacitive (from a capacitor) and inductive (from an inductor) reactances along with resistance combine as the impedance causing the opposition to the flow of AC current through the circuit.

For more info see Wikipedia: Electrical Reactance, Capacitor

Last edited by heroiclemon. Register to edit

Tags: none

Reactance — whether inductive or capacitive — opposes the flow of current. Inductive reactance varies proportionately with the frequency, so as frequency increases, the inductive reactance also increases.

(Capacitive reactance varies inversely with frequency.)

Notice that the equation for inductive reactance is defined with frequency, not amplitude:

\[X_L = 2\pi{f}L\]

\begin{align} X_L & = \text{Inductive reactance}\\ \pi & = \text{pi (3.14159...)}\\ f & = \text{Frequency}\\ L & = \text{Inductance}\\ \end{align}

The amplitude of the applied AC has no effect on reactance, eliminating two distractors.

For more info see Wikipedia: Electrical Reactance, Inductor

Silly way to help remember: How does an IN-ductor react to AC? As freq IN-creases, reACtance IN-creases. It's an IN-IN-IN! Also, indUctor goes up (capacitor goes down)

Last edited by kermitjr. Register to edit

Tags: none

As the frequency of the AC current applied to a capacitor increases, the reactance of the capacitor decreases.

The capacitive reactance is inversely proportional to the frequency. The higher the frequency of the AC current, the less charge can accumulate in the capacitor, and so the opposition to the current decreases.

Given:
\[ \begin{align} \pi &= 3.14…\\ f &= \text{frequency}\\ C &= \text{Capacitance}\\ \end{align} \]

\[\text{Capacitive Reactance }(X_C) = \frac{ 1 }{ 2\pi{f}C }\]

From the equation, one can see that as the frequency increases, the reactance of the capacitor decreases.

---

SILLY HINT: the band AC/DC - Frequency increases - CapACitor - DeCreases

---

From Wikipedia:

Reactance is the opposition of a circuit element to a change of electric current or voltage, due to that element's inductance or capacitance. A built-up electric field resists the change of voltage on the element, while a magnetic field resists the change of current. The notion of reactance is similar to electrical resistance, but they differ in several respects.

For more info see Wikipedia: Electrical Reactance, Capacitor

Last edited by kd7bbc. Register to edit

Tags: none

(D). When the impedance of an electrical load is equal to the internal impedance of the power source, the source can deliver maximum power to the load. When the impedances are equal they are said to be "matched". For both AC and DC currents matching the impedances causes the reactance of the system to be negligible or ideally, zero. This allows for maximum flow of current.

Silly hint: "you can't be resistive to Maximum Power"

For more info see Wikipedia: Impedance matching

Last edited by comdijital. Register to edit

Tags: none

(A). Impedance matching is important so that the source can deliver maximum power to the load. By matching impedances, the reactance becomes negligible or ideally, zero, leaving just resistance. If the impedances are not matched, the disparity in reactance along with resistance increases, and the power source can't transfer as much power to the load.

For more info see Wikipedia: Impedance matching

Last edited by N8GCU. Register to edit

Tags: none

The ohm (Ω) is the unit used to measure Reactance. The ohm is also the unit for electrical Impedance and Resistance, as these are all related properties that impede the flow of current in an AC circuit.

---

Resistance This is essentially friction against the flow of current. It is present in all conductors to some extent (except superconductors!), most notably in resistors. When the alternating current goes through a resistance, a voltage drop is produced that is in phase with the current. Resistance is mathematically symbolized by the letter “R” and is measured in the unit of ohms (Ω).

Reactance This is essentially inertia against the flow of current. It is present anywhere electric or magnetic fields are developed in proportion to an applied voltage or current, respectively; but most notably in capacitors and inductors.

When the alternating current goes through a pure reactance, a voltage drop is produced that is 90° out of phase with the current. Reactance is mathematically symbolized by the letter “X” and is measured in the unit of ohms (Ω).

Impedance This is a comprehensive expression of any and all forms of opposition to current flow, including both resistance and reactance. It is present in all circuits, and in all components.

When the alternating current goes through an impedance, a voltage drop is produced that is somewhere between 0° and 90° out of phase with the current. Impedance is mathematically symbolized by the letter “Z” and is measured in the unit of ohms (Ω), in complex form.

---

Perfect resistors possess resistance, but not reactance. Perfect inductors and perfect capacitors possess reactance but no resistance. All components possess impedance, and because of this universal quality, it makes sense to translate all component values (resistance, inductance, capacitance) into common terms of impedance as the first step in analyzing an AC circuit.

For more info see Wikipedia: Ohm, Electrical Reactance

Review of R, X, and Z (Resistance, Reactance, and Impedance)

Last edited by kd7bbc. Register to edit

Tags: none

(B). The Ohm is the unit used to measure impedance. The ohm is also used as the unit for both reactance and resistance, as these are properties of the total impedance, which all cause opposition to the flow of current in an AC circuit.

For more info see Wikipedia: Electrical Impedance, Ohm

Last edited by andresebastianmoreno. Register to edit

Tags: none

Though impedance matching is typically done with a balun, it is important to understand how other components will affect an antenna circuit. In this question, you can rule out the distractors of increasing or decreasing the power as these are not impedance matching. A circulator is typically a diode based device and therefore does not effect impedance. An LC Network contains an inductor (L) and capacitor (C). The key is the inductor as this component affects impedance. The correct answer is Insert an LC Network between the two circuits.

For more info see: Impedance matching, LC network

Hint: The key word is NETWORK.

Last edited by mhseeger73. Register to edit

Tags: none

One reason to use an impedance matching transformer is to maximize the transfer of power. This type of transformer alters the current and voltages, which changes the impedances between the power source and load. Matching the impedances allows for maximum power transfer, so this is one component which may be used for the function.

SILLY HINT: The correct choice has PRESENT which is closer in meaning to match, where the incorrect choices all have verbs that mean to make something smaller (minimize and reduce).

SILLY HINT 2 : The correct choice is the only one that includes "impedance"

For more info see Wikipedia: Impedance matching, Impedance Matching Transformer

Last edited by zayaan.raeid. Register to edit

Tags: none

All of the choices are correct. All of the listed devices are ones that can be used to match the impedances of the circuit frequency. Impedance matching is important as it allows for maximum transfer of power from the source to the load.

For more info see Wikipedia: Impedance matching

Last edited by kd7bbc. Register to edit

Tags: none