Login or Register for FREE!
Login or Register for FREE!
Subel. ZLG
10 questions
Subelement ZLG

Operating an Amateur Radio Station

Section ZLG23

General Operating Procedures

The correct order for callsigns in a callsign exchange at the start and end of a transmission is

  • Correct Answer
    the other callsign followed by your own callsign
  • your callsign followed by the other callsign
  • your own callsign, repeated twice
  • the other callsign, repeated twice
This question does not yet have an explanation! Register to add one

Tags: none

The following phonetic code is correct for the callsign "ZL1AN"

  • zanzibar london one america norway
  • Correct Answer
    zulu lima one alpha november
  • zulu lima one able nancy
  • zulu lima one able niner
This question does not yet have an explanation! Register to add one

Tags: none

The accepted way to call "CQ" with a SSB transceiver is

  • Correct Answer
    "CQ CQ CQ this is ZL1XXX ZL1XXX ZL1XXX"
  • "This is ZL1XXX calling CQ CQ CQ"
  • "CQ to anyone, CQ to anyone, I am ZL1XXX"
  • "CQ CQ CQ CQ CQ this is New Zealand"
This question does not yet have an explanation! Register to add one

Tags: none

A signal report of "5 and 1" indicates

  • very low intelligibility but good signal strength
  • Correct Answer
    perfect intelligibility but very low signal strength
  • perfect intelligibility, high signal strength
  • medium intelligibilty and signal strength
This question does not yet have an explanation! Register to add one

Tags: none

The correct phonetic code for the callsign VK5ZX is

  • victor kilowatt five zulu xray
  • Correct Answer
    victor kilo five zulu xray
  • victor kilo five zanzibar xray
  • victoria kilo five zulu xray
This question does not yet have an explanation! Register to add one

Tags: none

The accepted way to announce that you are listening to a VHF repeater is

  • "hello 6695, this is ZL2ZZZ listening"
  • "calling 6695, 6695, 6695 from ZL2ZZZ"
  • "6695 from ZL2ZZZ"
  • Correct Answer
    "ZL2ZZZ listening on 6695"
This question does not yet have an explanation! Register to add one

Tags: none

A rare DX station calling CQ on CW and repeating "up 2" at the end of the call means the station

  • Correct Answer
    will be listening for replies 2 kHz higher in frequency
  • will reply only to stations sending at greater than 20 wpm
  • is about to shift his calling frequency 2 kHz higher
  • will wait more than 2 seconds before replying to his call
This question does not yet have an explanation! Register to add one

Tags: none

When conversing via a VHF or UHF repeater you should pause between overs for about

  • half a second
  • Correct Answer
    3 seconds
  • 30 seconds
  • several minutes
This question does not yet have an explanation! Register to add one

Tags: none

Before calling CQ on the HF bands, you should

  • Correct Answer
    listen first, then ask if the frequency is in use
  • request that other operators clear the frequency
  • request a signal report from any station listening
  • use a frequency where many stations are already calling
This question does not yet have an explanation! Register to add one

Tags: none

The phrase "you are fully quieting the repeater" means

  • your signal is too weak for the repeater to reproduce correctly
  • Correct Answer
    your signal into the repeater is strong enough to be noise-free on the output frequency
  • your modulation level is too low
  • you are speaking too quietly into the microphone.
This question does not yet have an explanation! Register to add one

Tags: none

Go to ZLE20 Go to ZLG24
HamStudy.org™ is copyright 2024 Signal Stuff™, All rights reserved.
View Privacy Policy    |    Get help with HamStudy.org™