Answer: The delta matching system

An easy way to remember this is the two lines help form a triangle, or the Greek letter used as the fourth letter in the phonetic alphabet - \(\Delta\).

For a visual representation between a delta and a gamma match, see: here

Hint: The question says 'higher' impedance. Think Delta planes fly 'higher'.

Hint: The Greek letter Delta is used to indicate "change" in math and science, and we're changing impedance in the system.

Last edited by kd7bbc. Register to edit

Tags: none

A Gamma-match can match impedance below 50 ohms right up to that 50 ohms which your transceiver wants to see. A Yagi antenna almost never has an impedance of 50 ohms.

REF: http://www.dx-antennas.com/Gamma_match.htm

Silly Hint: Fraction starts with an F, which is one letter in the alphabet before G, which is the first letter in Gamma

Last edited by cq.n8gmz. Register to edit

Tags: none

Hint: A “SHORT length” = A “STUB.”

In microwave and radio-frequency engineering, a stub is a length of transmission line or waveguide that is connected at one end only. The free end of the stub is either left open-circuit or (especially in the case of waveguides) short-circuited. Neglecting transmission line losses, the input impedance of the stub is purely reactive; either capacitive or inductive, depending on the electrical length of the stub, and on whether it is open or short circuit. Stubs may thus be considered to be frequency-dependent capacitors and frequency-dependent inductors. Because stubs take on reactive properties as a function of their electrical length, stubs are most common in UHF or microwave circuits where the line lengths are more manageable. Stubs are commonly used in antenna impedance matching circuits and frequency selective filters.

http://en.wikipedia.org/wiki/Stub_(electronics)

Last edited by samdypaulson. Register to edit

Tags: none

The PVC insulation that encases the center conductor of a coaxial cable is within the outer tube that provides a series capacitance of some gamma-type matching networks.
The inductive reactance is cancelled by the series capacitance within the matching network. This will lead to a defined resonance.

Hint: "Matching Network" is in the answer.

Memory tip: The TV series was cancelled by the network

Last edited by schnugee. Register to edit

Tags: none

Think of the hairpin as a coil. It is a conductor with an inductive reactance. A tuned antenna is resonant which means inductive and capacitive reactances cancel each other out. For an inductor to tune an antenna the antenna must be capacitive.

Hint: Hairpin = Inductor, Inductors cancel Capacitors, to tune, we must have cancelled reactance. Thus The driven element reactance must be capacitive

Hint #2: Hairpin goes on your head. So does a baseball cap (Capacitive).

Silly hint: Reactance must be Capacitive so put a "Hairpin" in your "Cap"

Last edited by knguyen553. Register to edit

Tags: none

A hairpin matching system has inductive reactance, so an equivalent circuit can be constructed using an inductor (i.e. an L network).

Last edited by mvrog. Register to edit

Tags: none

The reflection coefficient is defined as

\[\Gamma = {(Z_L - Z_0) \over (Z_L + Z_0)}\]

where \(Z_L\) is the impedance of the load and \(Z_0\) is the characteristic impedance of the transmission line. If \(Z_0\) and \(Z_L\) are the same, the reflection coefficient (\(\Gamma\)) is zero. And the reflection coefficient increases the more \(Z_L\) and \(Z_0\) differ, indicating stronger mismatch between the load and transmission line.

Silly hint:the transmission line "reflected" on his behavior the day he lost Mrs Load

Hint: the lake had a "reflection" of the "line"

Last edited by jerryfaughn. Register to edit

Tags: none

Think of logic behind this problem. One ratio number must be higher than the other (it is the whole point of ratios). This is where SWR comes into play. SWR compares the impedance together.

Last edited by finbays. Register to edit

Tags: none

Tags: none

The impedance of a quarter wavelength matching transformer can be found by taking the square root of the product of the two impedances to be matched.

For this problem a 100 ohm impedance must be matched to a 50 ohm impedance.

\[\sqrt{50 \times 100}=\sqrt{5000} \approx 70.71\approx75\]

Therefore, a quarter (1/4) wavelength piece of 75-ohm coax should match the two impedances relatively well.

The formula for the impedance of a quarter wavelength matching transformer is: \[Z_{\text{in}}=\frac{Z_0^2}{Z_L}\Rightarrow Z_0=\sqrt{Z_{\text{in}}Z_L}\] where:

• \(Z_{\text{in}}\) is the input impedance

• \(Z_0\) is the characteristic impedance

• \(Z_L\) is the load impedance

Last edited by wileyj2956. Register to edit

Tags: none

Universal stubs are most used in VHF and higher applications to keep the feed line manageable. They are called universal because it can match unknown feed line and antenna impedances.

Last edited by wileyj2956. Register to edit

Tags: none

Memorization trick:

Each band goes on stage in phases at a concert

Also, driven element is mentioned in question and answer

Some beam antennas use multiple driven elements in order to make them multi-band antennas. The primary purpose of a phasing line when used with an antenna having multiple driven elements is that it ensures that each driven element operates in concert with the others to create the desired antenna pattern.

Last edited by kd7bbc. Register to edit

Tags: none

Tags: none